Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Motorline professional LINCE Series
Summary of Contents for Motorline professional LINCE Series
- Page 1 LINCE 230V/110V/24V USER’S AND INSTALLER’S MANUAL v11.0 REV. 05/2022...
-
Page 2: Table Of Contents
00. CONTENT 01. SAFETY INSTRUCTIONS INDEX STANDARDS TO FOLLOW 01. SAFETY INSTRUCTIONS ATTENTION: STANDARDS TO FOLLOW 02.PACKAGE This product is certified in accordance with European Community INSIDE PACKAGE (EC) safety standards. 03. OPERATOR CHANGE MOTOR DIRECTION This product complies with Directive 2011/65/EU of the European MANUAL RELEASE Parliament and of the Council, of 8 June 2011, on the restriction of TECHNICAL SPECIFICATIONS... -
Page 3: Safety Instructions
01. SAFETY INSTRUCTIONS GENERAL WARNINGS WARNINGS FOR TECHNICIANS • This manual contains very important safety and usage information. very important. Read all instructions carefully before beginning the • Before beginning the installation procedures, make sure that you have installation/usage procedures and keep this manual in a safe place all the devices and materials necessary to complete the installation that it can be consulted whenever necessary. - Page 4 01. SAFETY INSTRUCTIONS RESPONSABILITY • Disconnect means, such as a switch or circuit breaker on the electrical panel, must be provided on the product’s fixed power supply leads in • Supplier disclaims any liability if: accordance with the installation rules. •...
-
Page 5: Package
02. PACKAGE 03. OPERATOR INSIDE PACKAGE CHANGE MOTOR DIRECTION In the package you will find the following components: The operator LINCE, is a product developed exclusively for the automatic opening of swing gates. 01• 02 Swing operators LINCE 02• 01 Control Board Besides being pratical, safe and powerful, this product has a new function incorporated so 03•... - Page 6 03. OPERATOR 03. OPERATOR CHANGE MOTOR DIRECTION UNLOCK OPERATOR 03 • Loosen the screws of the Middle Part. 04 • Remove Middle Part. 01 • Remove the plastic cap from the rear Information engraved on the unlock shaft. end. D=Unlock || B=Lock 05 •...
-
Page 7: Technical Specifications 6A
03. OPERATOR 04. INSTALLATION TECHNICAL SPECIFICATIONS HEIGHT OF THE SUPPORTS The operator LINCE must be installed with a small inclination , to prevent water infiltration LINCE300 LINCE400 LINCE600 through the extension arm. 230V 230Vac 50/60Hz 230Vac 50/60Hz 230Vac 50/60Hz For this, the front support must be fixed to the gate with a height lower than the height of •... -
Page 8: Interior Opening Installation Quotas
04. INSTALLATION INTERIOR OPENING INSTALLATION QUOTAS On the Illustrated diagrams below and on the next page, are the dimensions for the installation of the automated system. * The installation of opening stopper is not mandatory. Axis of rotation of the (EXTERIOR) motor, on the front bracket Legend:... -
Page 9: External Opening Installation Quotas
04. INSTALLATION EXTERNAL OPENING INSTALLATION QUOTAS On the Illustrated diagrams below and on the next page, are the dimensions for the installation of the automated system. * The installation of opening stopper is not mandatory. Legend: *Opening Dimension X - Horizontal distance between hinge axis of the door and the rear axle of the motor. mechanical stopper Opening Dimension Y - Vertical distance between hinge axis of the door and the rear axle of the motor. - Page 10 04. INSTALLATION 04. INSTALLATION INSTALLATION STEPS INSTALLATION STEPS 04 • Install operator on the supports Pay attention to installation dimensions mentioned on pages 6B, 7 and 8! • The operator must be placed on both supports the same time to avoid leaving 01 •...
-
Page 11: Installation Map
04. INSTALLATION INSTALLATION MAP • CONTROL • INTERIOR • EXTERIOR • MOTOR LINCE • EXTERIOR • KEY • WARNING • ANTENNA BOARD PHOTOCELLS PHOTOCELLS PHOTOCELLS SELECTOR LAMP • JUNCTION LEGEND: • Connection cables It is important to use mechanical stoppers in the opening and closing position of the gate. It is important to use junction boxes for connections between motors, components and If not respected, components of the automation may suffer efforts for which they were not control unit. -
Page 12: Troubleshooting
05. TROUBLESHOOTING FINAL CONSUMERS INSTRUCTIONS INSTRUCTIONS FOR SPECIALIZED INSTALLERS Anomaly Procedure Behavior Procedure II Discovering the origin of the problem 1 • Open control box and check board and test them by connecting problem is on the control board. remove them from installation •Make sure you •... -
Page 13: Components Test
06. COMPONENTS TEST 06. COMPONENTS TEST 230V/110V MOTOR 24V MOTOR To detect if the malfunction is on the control board or on the motor is, sometimes, necessary To detect which are the components with problems in a 24V LINCE automatism instalation, to perform tests with connection directly to a 110V/230V power supply. -
Page 14: Maintenance
07. MAINTENANCE 07. MAINTENANCE MAINTENANCE MAINTENANCE • Clean the arm. • Check motor supports • With a cloth soaked in lubricant spray, wipe any residue that accumulates on the operator’s •Make sure that supports remain well fixed on the pillars and gate to ensure proper functioning of arm.
Need help?
Do you have a question about the LINCE Series and is the answer not in the manual?
Questions and answers