Set The Switches - Emerson Rosemount 3144P Quick Start Manual

April 2015
Function
Filter 50/60 Hz
Find Device
First Good Temperature Setup
Hardware Revision
HART Lock
Intermittent Sensor Detect
Lock Status
Long Tag
Loop Test
LRV (Lower Range Value)
Message
Open Sensor Holdoff
Percent Range
Sensor 1 Configuration
Sensor 1 Serial Number
Sensor 1 Setup
Sensor 1 Status
Sensor 1 Type
Sensor 1 Unit
Sensor 2 Configuration
Sensor 2 Serial Number
Sensor 2 Setup
Sensor 2 Status
Sensor 2 Type
Sensor 2 Unit
Sensor Drift Alert
Simulate Device Variables
Software Revision
Tag
Terminal Temperature Units
URV (Upper Range Value)
Variable Mapping
Thermocouple Diagnostic
Min/Max Tracking
Step 3: Set the switches
Switch HART revision mode
The 3144P comes with hardware switches to configure alarms and lock the
device. Use the following procedure to set the switches.
Without a LCD display
1. Set the loop to manual (if applicable) and disconnect the power.
2. Remove the electronics housing cover.
3. Set the alarm and security switches to the desired position. Reattach housing
cover.
4. Apply power and set the loop to automatic control.
HART 5 fast keys
2, 2, 7, 5, 1
N/A
2, 2, 3, 2
1, 8, 2, 3
N/A
2, 2, 7, 5, 2
N/A
N/A
3, 5, 1
2, 2, 5, 5, 3
2, 2, 7, 1, 4
2, 2, 7, 4
2, 2, 5, 4
2, 2, 1
2, 2, 1, 7
2, 2, 1
N/A
2, 2, 1, 2
2, 2, 1, 4
2, 2, 2
2, 2, 2, 7
2, 2, 2
N/A
2, 2, 2, 2
2, 2, 2, 4
2, 2, 4, 2
N/A
1, 8, 2, 4
2, 2, 7, 1, 1
2, 2, 7, 3
2, 2, 5, 5, 2
2, 2, 8, 5
2, 1, 7, 1
2, 1, 7, 2
Quick Start Guide
HART 7 fast keys
2, 2, 7, 5, 1
3, 4, 6, 2
2, 2, 3, 2
1, 11, 2, 3
2, 2, 9, 2
2, 2, 7, 5, 2
1, 11, 3, 7
2, 2, 7, 2
3, 5, 1
2, 2, 5, 5, 3
2, 2, 7, 1, 5
2, 2, 7, 4
2, 2, 5, 4
2, 2, 2
2, 2, 1, 8
2, 2, 1
2, 2, 1, 2
2, 2, 1, 3
2, 2, 1, 5
2, 2, 2
2, 2, 2, 8
2, 2, 2
2, 2, 2, 2
2, 2, 2, 3
2, 2, 2, 5
2, 2, 4, 2
3, 5, 2
1, 11, 2, 4
2, 2, 7, 1, 1
2, 2, 7, 3
2, 2, 5, 5, 2
2, 2, 8, 5
2, 1, 7, 1
2, 1, 7, 2
5