Advertisement
Elite Screens Slow Retract Manual Series Square Housing Dimension Table
Manual SRM Pro Series
Unit: mm
Screen
Aspect
Model
diagonal
ratio
M84HSR-Pro
84"
16:9
M100HSR-Pro
100"
16:9
M120HSR-Pro
120"
16:9
M84VSR-Pro
84"
4:3
M100VSR-Pro
100"
4:3
M120VSR-Pro
120"
4:3
* Dimension Table is only for reference, actual item might be different. Subject to change w/o notice.
Note: Data Error ±1"
Screen
Weight
material
Overall
View
bar
Width.
case
width
length
length (A)
（ A2 ）
(A1)
(A3)
2014
1936
1860
2010
2374
2290
2214
2370
2816
2733
2657
2812
1867
1783
1707
1863
2192
2108
2032
2188
2598
2514
2438
2594
Bottom
black
masking
Screen
border
material
with
Height with
View
weight
weight bar
Height
bar （ B2 ）
(B3)
(B1)
bar ( B)
62
1298
1046
62
1517
1245
62
1746
1494
62
1432
1280
62
1766
1524
62
2066
1829
Screen
Distance
overall
from
height
End
End
screen
with
cap
cap
material
weight
height
width
to the
(B4)
(C)
wall (C1)
1394
96
80
20
1613
96
80
20
1842
96
80
20
1528
96
80
20
1862
96
80
20
2162
96
80
20
Packing dimension
Top
black
masking
G.W.
L
W
H
border
(B5)
(KGS)
(mm)
(mm)
(mm)
190
8,24
2112
140
132
210
9,58
2472
140
130
190
####
2984
160
140
90
9,24
1965
150
140
180
9,48
2290
145
140
175
####
2666
140
135
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Elite Screens Manual SRM Pro Series
Summary of Contents for Elite Screens Manual SRM Pro Series
- Page 1 Elite Screens Slow Retract Manual Series Square Housing Dimension Table Manual SRM Pro Series Unit: mm Packing dimension Bottom black Screen Distance masking overall Screen from Screen border height Weight material screen black material with with Overall View Height with...
- Page 2 Manual SRMPro QUICK USER’S GUIDE Screen Installation A. Flush Wall Installation 1. Measure the distance of the keyholes on the end caps and mark the location of where the screen is to be installed for the pre-drilled hole. 2. After marking the area and drilling the hole, insert the proper screw into the drilled hole and leave about 1/8”...
- Page 3 ELITE SCREENS How to adding the spring force for Manual SRM Pro screen 1. Put the screen on the clean table, pull the material down a little and make it is in the locked state. As the picture shown below.
- Page 4 and affect the effect of re-adding the spring force） 4. Install the left end cap on the plastic part of the spring, rotating it in clockwise direction to add the spring force(rotating 10 laps), rotating it to a jammed point, that is, you feel the spring will not reverse by itself ,then you can release your hand.(when adding the spring force, pay attention to hold the end cap tightly to avoid it turn over and hitting hand)
- Page 5 6. Fixed the left end cap with the screws. ___________________________________ www.elitescreens.eu shop@elitescreens.eu...
Need help?
Do you have a question about the Manual SRM Pro Series and is the answer not in the manual?
Questions and answers