Table of Contents
Advertisement
[CONTRAST MODE]
(Correction mode setting)
[AUTO CONTRAST]
(Automatic light source
adjustment)
[BRILLIANT CORRECTION]
(Adjustment of aperture
diaphragm control)
[BRIGHT SIGNAL LEVEL]
(Setting of the brightness level
of the signal to start the light
adjustment)
[LIGHTS OUT TIMER]
(Time setting until the light turns
off)
[LIGHTS OUT SIGNAL
LEVEL]
(Setting of the brightness level
of the signal to turn off the light)
[LIGHTS OUT FADE-IN]
(Setting of fade-in when lighting
up again)
[LIGHTS OUT FADE-OUT]
(Setting of fade-out when
lighting off)
[MANUAL INTENSITY]
(Manual light source
adjustment)
[DYNAMIC GAMMA]
(Adjustment of signal
compensation)
[MULTI PROJECTOR SYNC]
104 - ENGLISH
Chapter 4 Settings — [PICTURE] menu
Setting item
[1]
[2]
[OFF]
[1] - [255]
[OFF]
[1]
[2]
[3]
[6%] - [50%]
[DISABLE]
[0.0s] - [10.0s]
[0%] - [5%]
[OFF]
[0.5s] - [10.0s]
[OFF]
[0.5s] - [10.0s]
[0] - [255]
[OFF]
[1]
[2]
[3]
Details
Select this item when misadjusted black level (grayish black) is
bothersome in the dark scenes.
Performs conventional correction to adjust the black level by
decreasing the general brightness.
Select this item when topical radiance is required even in dark
scenes.
Performs standard correction of the projector that does not
decrease the brightness too much.
(Factory default setting)
Does not adjust the light source.
The higher the value, the stronger the light adjustment of the light
source.
Can be set in increments of 1.
Does not correct brightness even in a scene with radiance.
Slightly corrects brightness in a scene with radiance.
Moderately corrects brightness in a scene with radiance.
(Factory default setting)
Strongly corrects brightness in a scene with radiance. This setting
will maximize the brightness.
Adjusts the light source when the brightness level of the image
signal being input gets lower than the set value. The higher the
value, the larger the range to perform the light adjustment of the
light source.
Can be set in increments of 1 %. (Factory setting: 30 %)
Does not turn off the light source.
Turns off the light source when the brightness level of the image
signal being input goes under the value set in [LIGHTS OUT
SIGNAL LEVEL].
Select an item from [0.0s] - [4.0s], [5.0s], [7.0s], or [10.0s]. [0.0s] -
[4.0s] can be selected in increments of 0.5.
Set the level of the brightness of the image signal to turn off the light
source with [LIGHTS OUT TIMER].
Can be set in increments of 1 %. (Factory setting: 0 %)
Does not set the fade-in of the image when the light source is
turned on again from the condition that the light source was turned
off with [LIGHTS OUT TIMER].
Sets the time to fade in the image when the light source is turned
on again from the condition that the light source was turned off with
[LIGHTS OUT TIMER].
Select an item from [0.5s] - [4.0s], [5.0s], [7.0s], or [10.0s]. [0.5s] -
[4.0s] can be selected in increments of 0.5.
Does not set the fade-out of the image when the light source is
turned off with [LIGHTS OUT TIMER].
Sets the time to fade out the image when the light source is turned
off with [LIGHTS OUT TIMER].
Select an item from [0.5s] - [4.0s], [5.0s], [7.0s], or [10.0s]. [0.5s] -
[4.0s] can be selected in increments of 0.5.
The larger the value, the stronger the correction.
Can be set in increments of 1. (Factory setting: 255)
Does not compensate the signal.
Slightly compensates the signal.
Moderately compensates the signal.
Strongly compensates the signal. This setting will maximize the
contrast.
Sets the contrast synchronization function.
This setting item is common with the following menu item.
f The [PROJECTOR SETUP] menu → [MULTI PROJECTOR
SYNC]
Refer to the [PROJECTOR SETUP] menu → [MULTI PROJECTOR
SYNC] (x page 176) for details.
Advertisement
Table of Contents
