Related Manuals for Fisher & Paykel HC60DCXB4
Summary of Contents for Fisher & Paykel HC60DCXB4
- Page 1 BOX WALL RANGEHOOD CONTEMPORARY HC60DCXB4, HC90DCXB4, HC90DCBB4 & HC120DCXB4 INSTALLATION GUIDE NZ AU...
-
Page 2: Safety And Warnings
SAFETY AND WARNINGS Installation WARNING! Please read the entire set of instructions before installing or using this appliance. Please make this information available to the person installing the appliance – doing so Electric Shock Hazard could reduce your installation costs. Always switch the power off prior to installation, servicing or cleaning of the appliance. - Page 3 SAFETY AND WARNINGS Never leave frying food unattended since grease can overheat and catch fire. The risk of fire is even greater in the case of used oil. Do not flambé under the rangehood. Never use the rangehood without the filters in place. During an electrostatic discharge (ESD) it is possible that the device will stop working.
-
Page 4: Components Required
COMPONENTS REQUIRED PARTS PARTS Keep all packing materials until the unit has been inspected. Not supplied Inspect the product to ensure there is no shipping damage. If any damage is detected contact the dealer or retailer you bought the product from to report the damage. Fisher &... -
Page 5: Product Dimensions
PRODUCT DIMENSIONS DATUM: REAR OF PRODUCT Model nos: HC60DCXB4 Product Dimensions a Maximum height of rangehood* 1035 B Minimum overall height - recirculating c Minimum overall height d Overall width of rangehood NOT TO SCALE e Overall depth of rangehood... -
Page 6: Back View
PRODUCT DIMENSIONS CEILING Model nos: HC60DCXB4 Product Dimensions a Lower rangehood attachment point width B Lower rangehood attachment point height c Upper rangehood attachment point height d Chimney bracket attachment point height e Light length f Distance from centre of light to front of product... - Page 7 PRODUCT DIMENSIONS DATUM: REAR OF PRODUCT Model nos: HC90DCXB4, HC90DCBB4 Product Dimensions a Maximum height of rangehood* 1035 B Minimum overall height - recirculating c Minimum overall height d Overall width of rangehood NOT TO SCALE e Overall depth of rangehood f Height of canopy TOP VIEW g Width of chimney...
- Page 8 PRODUCT DIMENSIONS CEILING Model nos: HC90DCXB4, HC90DCBB4 Product Dimensions a Lower rangehood attachment point width B Lower rangehood attachment point height c Upper rangehood attachment point height d Chimney bracket attachment point height e Light length f Distance from centre of light to front of product BACK VIEW DATUM: REAR OF PRODUCT BOTTOM VIEW...
- Page 9 PRODUCT DIMENSIONS DATUM: REAR OF PRODUCT Model nos: HC120DCXB4 Product Dimensions a Maximum height of rangehood* 1035 B Minimum overall height - recirculating c Minimum overall height d Overall width of rangehood 1198 e Overall depth of rangehood NOT TO SCALE f Height of canopy TOP VIEW g Width of chimney...
- Page 10 PRODUCT DIMENSIONS CEILING Model nos: HC120DCXB4 Product Dimensions a Lower rangehood attachment point width B Lower rangehood attachment point height c Upper rangehood attachment point height d Chimney bracket attachment point height e Light length f Distance from centre of light to front of product BACK VIEW DATUM: REAR OF PRODUCT BOTTOM VIEW...
-
Page 11: Installation Height
INSTALLATION HEIGHT Induction cooktop considerations Induction cooktops use energy efficient technology that only heats the contents of a cooking pot. Unlike gas or traditional electric cooktops, the surrounding air does not get heated when using an induction cooktop. As a result, rangehood filters, splashbacks and surrounding cabinetry do not get warmed up, increasing the likelihood of condensation on these cooler surfaces. -
Page 12: Venting Requirements
MODEL FREQUENCY VOLTAGE TOTAL POWER The rangehood can be installed to operate with the exhaust air ducted externally HC60DCXB4 from the kitchen, or installed to operate in recirculation mode with the exhaust air HC90DCXB4 recirculating within the kitchen. 50 Hz... - Page 13 INSTALL PREPARATION / CONSIDERATIONS Ducting options: Duct to roof and out external wall or Check for wall studs.* soffit. Duct to external wall and out. Ensure the space is set up to the correct specifications. Refer to ‘Installation height’ for details. One power outlet is required behind chimney.
- Page 14 CHECK MATERIALS AND PARTS UNPACK PRODUCT Open carton and remove all Ensure the ducting is the correct packaging. Carefully lift the products length and compatible to the out of the cartons. rangehood. Place on a protected surface. Dispose of packaging responsibly. Recycle where possible.
- Page 15 PREPARE INSTALL LOCATION Centre rangehood over cooktop and ensure all required clearances are maintained. Check wall for studs. Using the guide shown, mark the upper and lower attachment points on the wall. Drill attachment holes. Wood: 3mm diameter hole. Drywall or no wall stud: 5mm hole.
-
Page 16: Install Brackets
INSTALL BRACKETS INSTALL DUCTING RIGID DUCTING Centre and secure the upper and centre chimney brackets using two 30mm self tapping screws per bracket. If a cornice is present: Ensure the ducting is the correct length Move the upper chimney brackets lower and compatible to the rangehood. - Page 17 INSTALL DUCTING RIGID DUCTING Cut ducting to length. Fit ducting to the external vent and secure. Route ducting and assemble. Tape ducting to seal. If required, secure ducting within ceiling.
- Page 18 INSTALL DUCTING SEMI-RIGID DUCTING Ensure the ducting is the correct length Tape ducting to seal. and compatible to the rangehood. Install external venting as required. Weather proofing requirements depend If required, secure ducting within ceiling on the cladding/roofing type. Options to reduce noise.
-
Page 19: Prepare Hood
PREPARE HOOD INSTALL HOOD Install the 30mm upper hood Slot non-return valves into the adapter mounting screws* as per the product and ensure they move freely when dimension page. Ensure both screws installed. protrude 2mm. Lift the rangehood and slot onto the two upper hood mounting screws. -
Page 20: Install Chimney
SECURE DUCTING INSTALL CHIMNEY Remove the protective film from all chimney surfaces. Attach ducting to the adapter. Secure using tape, cable ties or metal straps as required. Ensure backdraft damper flaps are not Bend lower chimney tabs inwards using obstruted by the ducting. pliers. -
Page 21: Installer Checklist
INSTALL CHIMNEY INSTALLER CHECKLIST TO BE COMPLETED BY THE INSTALLER … Have all packaging been removed? Ensure filters are orientated correctly before clipping back into place. … Rangehood is correctly installed Remove all protective film from surfaces. … All connections are secure …... - Page 22 FISHERPAYKEL.COM © Fisher & Paykel Appliances 2023. All rights reserved. The models shown in this guide may not be available in all markets and are subject to change at any time. The product specifications in this guide apply to the specific products and models described at the date of issue.