Safety Measures - Vitek VT-1191 Manual Instruction

THERMOPOT VT-1191
An electric thermopot is intended for boiling water
and maintaining the required temperature of water
(pic. 1).
DESCRIPTION
Minimal water level mark «MIN»
1.
Water level scale
2.
Maximal water level mark «MAX»
3.
Spout for pouring water
4.
Control panel and digital display
5.
Lid opening button
6.
Steam release openings
7.
Removable upper lid
8.
Lid lock
9.
Carrying handle
10.
Body
11.
Power cord connector
12.
Sealing gasket
13.
Power cord
14.
Control panel and digital display
«Select Т °С / Timer» indicator
15.
« » («Boiling») indicator
16.
Maintain water temperature mode indicator
17.
« » («Maintain Т °С»)
«Current Т °С»
18.
Light sensor
19.
«REPEAT» («Re-boil») button
20.
Temperature selection button Select Т °С»
21.
Water supply button «
22.
Control panel unlock button «
23.
Power-saving mode button «ECO»
24.
Power saving mode indicator «ECO»
25.
ATTENTION!
For additional protection it is reasonable to install a
residual current device (RCD) with nominal opera-
tion current not exceeding 30 mA, to install RCD,
contact a specialist.

SAFETY MEASURES

Before using the unit, read this manual carefully
and keep it for future reference.
Use the unit for its intended purpose only, as speci-
fied in this manual.
•
Mishandling the unit can lead to its breakage
and cause harm to the user or damage to his/
her property.
•
Make sure that the operating voltage of the unit
corresponds to the voltage of your mains.
•
The power cord is equipped with a «euro plug»;
plug it into the socket with reliable grounding
contact.
»
» («Unlock»)
9
•
To avoid fire or electric shock, do not use adapt-
ers for plugging the unit in.
•
Do not use the unit in bathrooms. Do not use it
near swimming pools or other containers filled
with water.
•
Do not use the unit in places where aerosols are
sprayed or highly flammable liquids are used.
•
Do not use the unit outdoors.
•
Do not connect or disconnect the power cord
with wet hands, this may cause electric shock
or injuries.
•
When unplugging the unit, always pull the plug
but not the cord.
•
Never leave the operating unit unattended.
•
Do not switch the thermopot on if it is empty.
•
Do not drop or tilt the unit.
•
Be careful when using the thermopot to avoid
getting water on the electrical connector.
•
Use the thermopot only for water boiling; it is
prohibited to heat or boil other liquids in it.
•
Ensure that water level in the thermopot is not
below the «MIN» (1) mark and not above the
«MAX» (3) mark.
•
Do not fill the thermopot with water directly
from the faucet; to fill the thermopot use a suit-
able bowl.
•
Place the thermopot on a flat dry and stable sur-
face; do not place the thermopot on the edge
of the table.
•
Do not place the thermopot next to the walls or
close to the kitchen furniture.
•
Place the thermopot keeping at least 20 cm gap
between the thermopot body and the wall and at
least 30 cm gap above the thermopot.
•
Do not use the unit near heat sources and open
flame.
•
Do not let the power cord hang from the edge of
the table and make sure it does not touch hot or
sharp edges of furniture.
•
Do not open the lid and do not pour water out
during boiling. Be careful when you open the lid
right after water boiling.
•
Do not rotate the unit during water pouring.
•
Do not apply excessive effort when closing the
lid. When using the thermopot, make sure that
the lid is closed tightly.
•
Keep your hands away and do not bend over
the steam release openings (7), it may cause
burns. Do not block the steam release opening
with any objects.
•
Do not touch hot surfaces of the thermopot.
•
Be careful while carrying the thermopot filled
with boiling water.
ENGLISH