Vitek VT-1191 Manual Instruction page 11

reaches 40°C, the thermopot will automatically
enter the maintain temperature mode and the
indicator light (16) on the display will go out
and the maintain temperature mode indicator
light (17) will come on.
Notes:
– every pressing of the control buttons is accom-
panied by a sound signal;
– the operation mode buttons on the control
panel (5) are sensory, you just need to touch
the button to switch the necessary operation
mode on.
•
Drain the water; to do this, unlock the buttons
on the control panel (5) by pressing the «
button (23) (pic. 4), place a suitable container
under the water drain spout (4) and press the
« » button (22) (pic. 6) and hold the button
down until the water fills the container to the
desired level.
Note: If, after unlocking, no action is taken for
15 seconds, the lock will be switched on again au-
tomatically and the locking indicator (20) will light
up again.
Attention! Be careful when pouring out water to
avoid burns by hot water.
•
To switch the thermopot off disconnect the
power plug (14) from the mains socket.
•
Open the thermopot lid (8) and wait until it cools
down completely.
•
Carefully tilt the thermopot to drain the remain-
ing water.
•
Install the lid (8) back to its place. Before using
the thermopot make sure that the lid (8) is fixed
properly and the button (6) is pressed.
•
The thermopot is ready to use.
USING THE THERMOPOT
•
Open the lid (8) by pressing the button (6), take
the lid and pull upwards (pic. 2,3).
•
Fill the thermopot with water using a suitable
bowl, do not exceed the «MAX»(3) water level
mark. Do not pour water above the mark «MAX»
(3), as hot water may splash out when boiled.
•
Insert the plug of the power cord (14) into the
slot (12) on the body of the thermopot, and plug
the power cord (14) into the mains. You will hear
a sound signal, and all indicator lights on the dis-
play will turn on for several seconds.
Temperature selection
To change the required maintaining temperature
consequently press the water temperature setting
button (21) «Select T °С». The maintain tempera-
ture selection can be varied in the range «CO/40/
45/50/55/60/65/70/75/80/85/90/95/100°C»,
where «СО» is the temperature self-cooling mode.
•
The set temperature to be maintained is shown
on the display indicator (15).
•
Next, depending on the current water temper-
ature (indicator (18)), the thermopot will auto-
matically heat the water to the set temperature
(indicator (15)).
Note: If the selected temperature is lower than the
temperature in the thermopot, then the water in the
thermopot will first cool down to the set temperature,
after that the selected temperature will be main-
» tained. When the water temperature in the thermo-
pot drops below the set temperature by more than 5
degrees, the thermopot will switch to heating mode.
WATER DISPENSE AND WATER DOSING
FUNCTION
Water dispense for 5 seconds
•
First press the «
function buttons on the control panel (5) will light
up, indicating that the control panel is unlocked,
and then press the «
the thermopot continuously dispenses water
for 5 seconds, the «Timer» indicator (15) on the
display shows the countdown in seconds (water
supply from 200 to 250 ml). If you want to stop
dispensing water, press the «
stop the water dispense).
Continuous water dispense
•
First press the «
five function buttons on the display light up,
it means that the control panel is unlocked.
Then press and hold the «
start the water dispense (pic. 6).
At the same time, the «Timer» indicator (15) on
the display shows a direct countdown in seconds
The water supply will stop when you release the
button (22).
Boiling and re-boiling
Press button (23) «
(5) (pic. 4).
•
Press the button (20) «REPEAT» to start the
water boiling process. The «
(16) will start flashing on the display
Notes:
– The thermopot uses a long boiling technology
which allows to significantly reduce the chlorine
level in water.
– Do not open the upper lid during water boiling.
– Do not block the steam outlet opening (7).
11
ENGLISH
» button (23) (pic. 7), the five
» button (22) (pic. 6),
» button again to
» button (23). When the
» button (22) to
» to unlock the control panel
» indicator