Cleaning And Maintenance - Vitek VT-2660 Manual Instruction

ENGLISH
• To switch on the constant steam supply mode,
lock the steam release button (2), to do this, press
the button (2) and slide the latch (3) down. To turn
off the constant steam supply, move the latch (3)
to the upper position.
Note: do not direct the steam on metal buttons or
accessories.
ATTENTION!
– During the operation, the operating surface (4)
and the upper part of the body (5) become very
hot, do not touch the operating surface (4) and
the upper part of the body (5), and beware of get-
ting burned by hot steam.
– If you use the garment steamer without the brush
attachment (9), keep the operating surface (4) at
at least 5 cm from the clothes.
• Slowly run the steamer down the fabric, straight-
en the folds on the fabric with your free hand. Do
not place your hand under the steamed fabric
while switching the steam supply on.
• When steaming the clothes sleeves, start from
the top of the sleeve and move the steamer down.
Straighten the sleeve downwards and diagonally
with your free hand.
• When smoothing pockets on a shirt, move the
steamer up.
• After finishing work, unplug the power cord from
the electrical outlet to turn off the steamer.
• Take out the water tank (1), open the lid (8) and
pour out the remaining water, put the tank (1)
back in place.
Note: the clothes should cool and dry after steam-
ing, this may take some time.
USING THE BRUSH ATTACHMENT
ATTENTION! Before installing the brush attachment
(9), make sure that the operating surface (4) has
cooled down and that the power plug is not connected
to the mains.
• The brush attachment (9) removes lint and dirt from
the clothes, makes smoothing of the folds easier
and allows to steam thick and heavy fabrics.
• Magnetic attachment system for the brush (9)
ensures quick attachment and removal of the
brush (9).
Possible troubles and troubleshooting:
Malfunction
The garment steamer The power plug is not inserted into the
is not switched on. socket.
No voltage in the socket.
No steam release. The steamer didn't heat up to the
required temperature.
You do not press the steam supply
button completely.
Not enough water in the water tank.
The water tank is not installed properly.
You turned the steamer over.
• Place the brush (9) on the work surface (4), make
sure that the brush (9) is securely fixed.
• To turn on the steam release, press and hold the
button (2), the water pump will turn on and you
will hear a characteristic sound, this is normal.
To switch the steam supply off, release the but-
ton (2).
• To switch on the constant steam supply mode, lock
the steam release button (2), to do this, press the
button (2) and slide the latch (3) down. To turn off
the constant steam supply, move the latch (3) to
the upper position.
• After finishing work, unplug the power cord from
the electrical outlet to turn off the steamer.
• Remove the brush attachment (9).
• Take out the water tank (1), open the lid (8) and
pour out the remaining water, put the tank (1) back
in place.

CLEANING AND MAINTENANCE

• Disconnect the power plug from the mains sock-
et and let the garment steamer cool down com-
pletely.
• Take out the water tank (1), open the lid (8) and
pour out the remaining water, put the tank (1)
back in place.
• Clean the steamer body and the operation sur-
face (4) with the steam release openings with a
slightly damp cloth, and then wipe dry.
• You can remove the mineral deposits from the
operating surface (4) with a cloth soaked in the
water and vinegar solution.
• Rinse the brush attachment (9) under running
water and dry.
• Do not use abrasive cleaners and solvents to
clean the garment steamer.
• Do not immerse the steamer, the power cord and
the power plug into water or other liquids.
STORAGE
• Unplug the steamer and wait till it cools down
completely.
• Clean the steamer.
• Keep the unit in a dry cool place out of reach of
children and disabled persons.
Cause
Insert the power plug into the mains
socket.
Insert a known good appliance into
the socket; if the socket malfunctions,
contact the appropriate service.
Wait for the steamer to heat up, the
indicator light should turn off.
Press the steam supply button as far as
it wil go.
Fill the water tank with water.
Make sure that the water tank is
installed properly.
The steamer is intended for operating
only in vertical position.
10
Solution