Table of Contents
Advertisement
WARNING:
Disconnect tool from its power source before actuator removal or installation. Severe personal injury may occur if
power source is not disconnected.
CAUTION:
Actuator assembly-air (704130) can break if not careful.
CAUTION:
Do not over tighten actuator assembly-air (704130). Snug tighten only.
REMOVING ACTUATOR ASSEMBLY-AIR (704130)
1.
Remove actuator lever assembly (704343) and pin-slotted (400608) from the
handle-split (700326).
2.
Insert a 5/8" open end / adjustable wrench around actuator assembly-air (704130).
3.
Loosen the actuator assembly-air (704130).
4.
Remove wrench. Unthread and remove the actuator assembly-air (704130)
with fingers from the handle-split (700326).
INSTALLING ACTUATOR ASSEMBLY-AIR (704130)
1.
Apply Teflon® tape onto threads of actuator assembly-air (704130) one to two wraps.
2.
Thread the actuator assembly-air (704130) all the way into handle-split (700326) with
fingers.
3.
Insert and turn 5/8" open end / adjustable wrench and snug tight approximately 1/4 - 1/2 turn.
4.
Reattach actuator lever assembly (704343) and pin-slotted (400608) to the handle-
split (700326).
To disassemble nose assembly from tool, take the following steps:
1. Disconnect air supply to tool.
2. Loosen and removed fitting-regulator (703627) then pull out insert
(731355) from rear of cap-vacuum (731418).
3. Loosen and remove retaining nut (211102), retaining nut stop (240102),
and anvil holder assembly.
4. Attach wrench to flats on collet and insert 1/4" Allen wrench (comes
with tool) into hex in rear of piston (731211) and remove remaining
nose assembly parts (IE* collet, extension-collet & jaws). (Individual
parts vary depending on nose assembly).
5. Assembly is the opposite of disassembly. Follow steps in reverse to
assemble your nose assembly. (See also nose assembly data sheet).
* See overhaul and parts lists on pgs. 16 - 19 for more assembly or
disassembly information.
* Insert (731355) must be removed (before assembly/disassembly of noses)
to install Allen wrench into rear of piston.
To assemble nose assembly to tool, take the following steps:
1. Hand thread and tighten assembled collet (with jaw) and extension-collet to piston on tool. (Individual parts vary depending on
nose assembly). See proper data sheet for more information.
2. With insert (731355) removed, insert 1/4" Allen wrench (comes with tool) into hex in rear of piston (731211) and Attach wrench to
flats on collet and tighten assembly to piston on tool. See proper data sheet for more information.
3. Slide anvil assembly over collet then slide retaining nut stop and retaining nut over anvil assembly and thread and tighten retaining nut to tool.
(Note: Retaining nut stop fits into ears on anvil. See proper data sheet for more information).
4. With 1/4" Allen wrench removed from rear of piston and end cap on tool, place insert (731355) into rear of cap-vacuum until flush.
(NOTE: Insert (731355) is only used on 3/16" and 5mm" nose assemblies. DO NOT use with 1/4" or 6mm nose assemblies).
5. Attach and tighten the fitting-regulator (703627) with pintail evacuation tube to the cap-vacuum (731418).
* See overhaul and parts lists on pgs. 16 - 19 for more assembly or disassembly information.
* Insert (731355) must be removed (before assembly/disassembly of noses) to install Allen wrench into rear of piston.
(NOTE: Insert (731355) is only used on 3/16" and 5mm" nose assemblies. DO NOT use with 1/4" or 6mm nose assemblies).
GB731SHV5/LB68 INSTALLATION TOOL: SERIAL # 1001 & ABOVE
CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
OVERHAUL
ACTUATOR ASSEMBLY-AIR
NOSE ASSEMBLY / DISASSEMBLY
Images may not reflect actual tool.
16
*Use 731355 insert with 3/16" and 5mm only.
DO NOT use with 1/4" or 6mm
2/19 REV. 1/23
Advertisement
Table of Contents
