Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for EdilKamin 809540
Summary of Contents for EdilKamin 809540
- Page 1 PELLKAMIN2 12 PELLET FIREPLACE 809540 809570 Installation, use and maintenance...
-
Page 2: Table Of Contents
Troubleshooting Troubleshooting ALWAYS PAIR PELLKAMIN2 12 codes 809540 and 809570 WITH TWO VENTILATED AIR VENTS POSITION THEM AT A MAXIMUM OF 1.5 m Ventilated air vents and accessory kits for air vents are NOT included with the product PELLKAMIN2 12 The undersigned company, EDILKAMIN S.p.A., with... - Page 3 Proper commissioning is required for activation of the Edilkamin warranty. The warranty is only valid in the MEANING OF SYMBOLS In some parts of the manual the following symbols country of sale of the product.
-
Page 4: Safety Information
DO NOT the warranty certificate inside the product: neither CLIMB ONTO THE PRODUCT OR USE IT AS A Edilkamin nor the reseller are liable for damage SUPPORT. Risk of damage and injury. resulting from incorrect installation or maintenance. -
Page 5: Dimensions
DIMENSIONS PELLKAMIN2 12 with ducted ventilation and a pellet loading trapdoor 87.5 Ø 8 smoke outlet Ø 15 trapdoor loading Ø 10 60.5 ducted air PELLKAMIN2 12 with ducted ventilation and a pellet loading drawer 87.5 Ø 8 smoke outlet 60.5 Ø... - Page 6 NOTES ON DIMENSIONS Example of minimum recommended dimensions for installation with fans at the bottom and optional stand at minimum height. This example for illustrative purposes only. Holes should also be made for: the fume discharge (flue); the combustion air inlet; ventilation air recovery (a 10x10 cm hole in the side of the covering) 30/40 87,5...
-
Page 7: Technical Data
2,4 GHz Logic board protection Fusibile T4A, 250 Vac 5x20 The above data are illustrative and are drawn from the certification by a notified body. EDILKAMIN s.p.a. reserves the right to modify the product without notification in the interests of improvement. -
Page 8: Unpacking
UNPACKING PREPARATION AND UNPACKING CONTENTS OF PACKAGE The packaging materials are neither toxic nor noxious The packaging materials are neither toxic nor noxious The packaging varies according to the Pellkamin and do not require special disposal. and do not require special disposal. version. - Page 9 UNPACKING , undo screws TO UNPACK THE PRODUCT (A) as shown below To facilitate handling, the PELLKAMIN2 12 is fitted with handles (B). Do not use the air intake or fumes outlet to handle the appliance. This may lead to slight misalignments.
-
Page 10: Packaging
PACKAGING Version cod. 809540 with pellet loading trapdoor • the Pellkamin frame • the trapdoor loading system • the two compensation vents • the inlet surround Version cod. 809570 with pellet loading drawer • the Pellkamin frame • the two compensation vents •... - Page 11 INSTALLATION SUMMARY INSTALLATION CHECKS SUMMARY INSTALLATION CHECKS For details, refer to the respective pages of this manual. For details, refer to the respective pages of this manual. Element to be checked Element to be checked What to check What to check Suitability of the room Suitability of the room •...
- Page 12 • must have at most 3 bends, through an angle of Contact the authorised Edilkamin Technical Assistance no more than 90° Centre. • must have a single horizontal section of length no more than 3 metri, depending on the draw.
- Page 13 INSTALLATION THE FLUE THE FLUE: EXTERNAL AIR INTAKE EXTERNAL AIR INTAKE In general, we suggest two ways to ensure a proper Further to the general prescriptions for the fumes duct flow of combustion air. and flue, the flue: : Air intake without direct connection to the •...
- Page 14 The electrical system must be compliant; check • the lower terminal board (high voltage) is for the the operation of the earth in particular. Edilkamin is electrical power and fan connections; not responsible for malfunctions resulting from an improperly grounded system. The power line must be these connections may be made by a of adequate section for the power of the appliance.
-
Page 15: Installation
INSTALLATION HEIGHT OF APPLIANCE HEIGHT OF APPLIANCE MOUNTING TO THE BASE MOUNTING TO THE BASE The Pellkamin can be mounted on an optional stand or Use the provided screws to secure the appliance to any other appropriate support the base OPTIONAL BASE OPTIONAL BASE Place the bottom of the base (1) in the desired... - Page 16 LOADING TRAPDOOR INSTALLING THE LOADING TRAPDOOR INSTALLING THE LOADING TRAPDOOR Step 1: INSTALLING THE LOADING HATCH Step 1: INSTALLING THE LOADING HATCH Reinforce the plasterboard with metal profiles at the The loading kit includes: back. • loading tube • Make a hole 31 x 21 •...
- Page 17 PELLKAMIN2 12 can be combined with the following PELLKAMIN2 12 can be combined with the following You need: You need: Edilkamin air vents: Edilkamin air vents: two ventilated air vents (models of your two ventilated air vents (models of your •...
- Page 18 PELLET LOADING DRAWER Kit for pellet tank Kit for pellet tank posizionarli all'interno del serbatoio pellet (place them inside the pellet tank) Regolare i part. A,B,C e fissarli con viti part. D (adjust the parts A, B, C and fix them with screws part.
- Page 19 PELLET LOADING DRAWER CONTENTS CONTENTS • • Drawer Kit (2) Drawer Kit (2) • • ceramic front panel with support (3) ceramic front panel with support (3) ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS 1. 1. unscrew the metal cover (1) on the top part of the frame unscrew the metal cover (1) on the top part of the frame 2.
- Page 20 PELLET LOADING DRAWER repeat on the Connecting the pipes for ducting hot air other side (4 screws) Figure 11 Connecting Drawer fitted pipes for ducting Figure 12 hot air...
- Page 21 NOTES ON CLADDING INSTALLING THE CLADDING - INSTALLING THE CLADDING - PRECAUTIONS PRECAUTIONS Regardless of the type of cladding (whether pre- existing or new) make sure that: • the compensation vents are present so that the mantel does not accumulate heat and damage the ventilation kit;...
- Page 22 INLET SURROUND For versions INLET SURROUND INLET SURROUND 2. with frontal ventilation and pellet loading trapdoor The inlet surround is used to fill the gap remaining (see fitting frontal ventilation Kit) between the fireplace frame and the cladding. 3. with frontal ventilation and pellet loading trapdoor The surround has an opening on one long side.
-
Page 23: Instructions For Use
INSTALLATION FIRST IGNITION (COMMISSIONING) PHASES FUEL • Make sure you have read and understood this manual Use UNI EN ISO 17225-2 category A1 wood pellets Use UNI EN ISO 17225-2 category A1 wood pellets • Remove all flammable materials from the appliance or similar regulatory products with the following or similar regulatory products with the following (manuals, labels, etc.). - Page 24 USER INSTRUCTIONS OPERATION PHASES Further to the above operational procedures, the Description. The access to and adjustment of these product has the following phases functions is described below: - Ignition (display reads ON ) Flame ignites and grows stable Mode Size settings This is the result of: MANUAL...
- Page 25 • Open the back of the remote and insert the use. Edilkamin and the reseller will not consider two batteries in the indicated orientation. claims for battery life under any circumstances. If •...
- Page 26 USER INSTRUCTIONS The display reads the POSSIBLE STATES described below: - OFF STATE The fireplace is shutting off or is off in response to operation of the remote control’s ON/OFF key or an external contact (crono, phone dialler) The display shows the current time, room temperature and the status in relation to which the fireplace is OFF.
- Page 27 We describe the procedures below. In the event of the installation of the optional front fan, fans 2 and 3 will not be present and the Edilkamin technician will explain the new operating mode during ON/OFF installation.
- Page 28 USER INSTRUCTIONS - Stand by - Relax function When the Stand by function is active, in automatic Natural convection function with automatic power and timer modes, the product shuts off when the limiting. temperature setpoint is reached and turns on again This function is available in all modes: automatic, when the temperature drops.
- Page 29 USER INSTRUCTIONS Crono The following screen will appear. Scroll to “ENABLE” (underlined) using the “+/-” buttons. When the Crono function is active, the user sets a To enable the Crono function to 7 days a week or temperature setpoint and a time zone for which that on single days (“ENABLE”...
- Page 30 USER INSTRUCTIONS To set the temperature setpoints (“TEMP” on To combine one of the three temperatures the display), from the Crono function, press the “OK” to a time period (“SET” on the display), from the button. The following screen will appear. Crono function, press the “OK”...
- Page 31 USER INSTRUCTIONS The second screen (accessible by pressing the “OK” To view/change the settings (“CHANGE” on button from the first screen) allows you to set the start the display), from the Crono function, press the “OK” and end time of the time period matching the chosen button.
- Page 32 USER INSTRUCTIONS Night (deferred switching on/off) Load Pellets This function switches the product on/off after a set Allows you to load pellets after the screw feeder has emptied following a no-pellets alarm. period from activation of the function. Useful for the technician during commissioning. This is convenient if you go to bed and want the product Available only in the OFF state.
- Page 33 USER INSTRUCTIONS Date/Time Beep Sets the current date/time. Allows you to enable/disable the beep. This displays the first time the remote control is To access the function from the main menu (as activated with the stove powered on, or by selecting indicated in the Menu section above), press the M the option in the menu.
-
Page 34: Maintenance
MAINTENANCE Before doing any maintenance, disconnect Never vacuum hot ash, it can the appliance from the mains. make vacuum cleaner breakdown and represents a fire Regular maintenance essential risk. keeping the appliance in good working order. Do not empty the residue out into FAILURE TO SERVICE THE Fireplace WILL the pellet hopper. - Page 35 MAINTENANCE DAILY MAINTENANCE Note that using the fireplace without cleaning the grate can This must be done with the appliance switched off cause the gas in the combustion and cold. chamber to ignite and break the It must be done with a vacuum cleaner door glass.
- Page 36 SPARE PARTS For any spare parts, contact your reseller or technician. Using non-original spare parts may damage the appliance and relieves Edilkamin of all liability for damage resulting therefrom. DISPOSAL At the end of its service life, dispose of the product as required by regulations.
-
Page 37: Troubleshooting
TROUBLESHOOTING If problems occur, the fireplace shuts itself off automatically. The display will show the reason (see below). DO NOT disconnect the electrical power supply. To start the product up again, allow the shutdown procedure to complete, then press the remote control's ON/OFF button or the simplified ignition button. - Page 38 The battery symbol displays on the remote’s display if the battery is low. MAINTENANCE: A wrench symbol is shown on the display after 2000 hours of operation. The product is working, but it must be serviced by an authorised Edilkamin technician.
- Page 40 *942076-GB* w w w . e d i l k a m i n . c o m cod. 942076-GB 04.19/A...