Adjustable case sealer with accuglide ii taping heads (72 pages)
Summary of Contents for 3M Matic 8000a-I
Page 1
Instructions and Parts List 3M-Matic 8000a-I / 8000a3-I ™ Type 11700 Adjustable Case Sealer with AccuGlide 3 Taping Heads ™ Serial #: For reference, record machine serial number here. Important Safety Information BEFORE INSTALLING OR OPERATING THIS EQUIPMENT Read, understand and follow all safety and operating instructions.
Page 2
International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page ii 44-0009-2161-7 / ECO# 0078483...
Page 3
Replacement Parts and Service Information To Our Customers: This is the 3M-Matic /AccuGlide /Scotch equipment you ordered. ™ ™ ® It has been set up and tested in the factory with Scotch Tapes. ® If technical assistance or replacement parts are needed, call or fax the appropriate number listed below.
Page 4
International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page iv 44-0009-2161-7 / ECO# 0078483...
Page 5
EU DECLARATION OF CONFORMITY Original Name and address of the manufacturer and, where applicable, his authorised representative: 3M Deutschland GmbH, Closure and Masking Systems Division Carl-Schurz-Strasse 1 D41453 Neuss, Germany This declaration of conformity is issued under the sole responsibility of the manufacturer.
Page 6
Replacement Parts and Service Information To Our Customers: This is the 3M-Matic /AccuGlide /Scotch equipment you ordered. It has been set ™ ™ ® up and tested in the factory with Scotch tapes. If any problems occur when operating ®...
4.12 Machine and Packaged Machine Dimensions . . . . . . . . . . . . . . . . . . . . .15 International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™...
Page 8
International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page viii 44-0009-2161-7 / ECO# 0078483...
Page 9
11.6 Run Boxes to Check Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™...
Page 10
International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page x 44-0009-2161-7 / ECO# 0078483...
Page 11
Drawings and Parts Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 – End of Manual Taping Head Information Manual 2 and 3: AccuGlide 3 Taping Heads — 2 Inch or 3 Inch ™ (See Manual 2 or 3 for Table of Contents) International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page xi 44-0009-2161-7 / ECO# 0078483...
Page 12
AccuGlide ..Trademark of 3M St. Paul, MN 55144-1000 Scotch ..Trademark of 3M St. Paul, MN 55144-1000 Drw... . Drawing Ex.
The 8000a-I / 8000a3-I is manually adjustable to a wide range of box sizes (see “Specifications Section – Box Weight and Size Capacities”). The 3M-Matic case sealing machines have been designed and manufactured in compliance with the legal requirements at the date of inception.
2.1 Data Identifying Manufacturer and Machine Identi cation Plate Data for Technical Assistance and Service Agent/Distributor or Local After Sale Service: International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 3 44-0009-2161-7 / ECO# 0078483...
Page 16
Contents: 8000a-I / 8000a3-I Adjustable Case Sealer (1) 8000a-I / 8000a3-I Adjustable Case Sealer, Type 11700 (1) Tool and Spare Parts Kit (1) Instruction and Parts Manual International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 4...
Warning hazardous situation, Physical Earth which, if not avoided, connection could result in death or serious injury and/ or property damage. International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 5 44-0009-2161-7 / ECO# 0078483...
Never put your hands inside any part the machine is running. of the machine while it is working. Serious injury may occur (Figure 3-4). International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 6 44-0009-2161-7 / ECO# 0078483...
Page 19
- Always feed boxes into the machine Figure 3-8 by pushing only from the end of box. International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 7 44-0009-2161-7 / ECO# 0078483...
- The operator must pay attention qualified personnel to operate and to the blades during the tape service this equipment. replacement. International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 8 44-0009-2161-7 / ECO# 0078483...
Page 21
Stopped by pressing Adjusting box size the EMERGENCY STOP Tape replacement button Blade replacement Electric power Drive belt replacement disconnected Ordinary maintenance International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 9 44-0009-2161-7 / ECO# 0078483...
Electrical – 230/400 Volt, 50 Hz., SCCR: 5kA The machine is equipped with a 2.4m [8 foot] standard neoprene covered power cord. Contact your 3M Representative for power requirements not listed above. 4.2 Operating Rate: Belt speed is 0.5m/s [100 F.P.M.] Actual production rate is dependent on operator’s dexterity.
The sum of measured value of noise plus its associated uncertainty represents an upper limit of range of values. Idling refers to machine running in rest position (no boxes). Under Load refers to machine running and box taping using adhesive tape 3M-Scotch 75mm (3”) Accuglide - Bottom Taping Head.
Page 26
Special modifications may be available for carton sizes not listed on previous page. Contact your 3M Representative for information. Note: The case sealer can accommodate most boxes within the size range listed above. However, if the box length (in direction of seal) to box height ratio is .6 or less, several boxes should be test run to assure proper machine performance.
- Do not stack anything over machine. Figure 5-4 - It is possible to stack a maximum of 2 machines (if in original packing). International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 16 44-0009-2161-7 / ECO# 0078483...
- Polyethylene protective material For the disposal of the above materials, please follow the environmental directives or the law in your country. Figure 6-5 International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 17 44-0009-2161-7 / ECO# 0078483...
5 - For Outer Column Positioning - The columns are shipped in a lower position. To Adjust Columns - See Special Figure 7-3 Set-up Procedure (Section 11). International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 18 44-0009-2161-7 / ECO# 0078483...
Important: All connections must be made by a end of the lower frame quailfied electrical service technician. (as shown in Figure 7-9). International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 20 44-0009-2161-7 / ECO# 0078483...
8.3.2 Emergency Stop The LATCHING EMERGENCY STOP BUTTON is located on the top center of the machine (Figure 8-3). Belt Direction Figure 8-3 International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 21 44-0009-2161-7 / ECO# 0078483...
• Have wire size 1.5mm dia. [AWG 16] personnel to operate and service this • Have a max. length 30.5m [100 ft] • Be properly grounded. equipment. International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 23 44-0009-2161-7 / ECO# 0078483...
[2.0 inches], refer to Instructions below and also to Manual 2 or 3, “Removing Taping Heads Procedure - Changing the Tape Leg Length”. Figure 11-3 International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 24 44-0009-2161-7 / ECO# 0078483...
Page 37
Also tighten two Set Screws (if applicable) (continued on next page) Note: Loosen but do not Remove Column Screws 305mm Min. Figure 11-7 International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 25 44-0009-2161-7 / ECO# 0078483...
Important – If drive belts are allowed to slip on box, excessive belt wear will occur. International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 26 44-0009-2161-7 / ECO# 0078483...
2. Latching emergency stop button electric power (Figure 12-3). 3. STOP (OFF) (O) main switch International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 27 44-0009-2161-7 / ECO# 0078483...
Adjust belt tension Electrical disconnect Check power and electrical plug Motor not turning Evaluate problem and correct (continued on next page) International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 28 44-0009-2161-7 / ECO# 0078483...
Page 41
The tape is threaded incorrect Rethread tape Applying mechanism spring Move spring hook to next has too little tension tighter hole International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 29 44-0009-2161-7 / ECO# 0078483...
Page 42
International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 30 44-0009-2161-7 / ECO# 0078483...
International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 31 44-0009-2161-7 / ECO# 0078483...
Page 44
13. Maintenance and Repairs (continued) 13.8 Box Drive Belt Replacement Warning Note – 3M recommends the replacement of drive belts in pairs, especially if belts • To reduce the risk associated with are unevenly worn. mechanical and electrical hazards: 1. Crank the upper taping head to its fully raised position.
- Turn electrical supply off and disconnect Drive Belts”, steps 3 and 7. before performing any adjustments, maintenance or servicing the machine or taping heads. International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 34 44-0009-2161-7 / ECO# 0078483...
70 to 48mm [2-3/4 to 2 inches] – Manual 2 or 3 Leg Length” for taping head set-up. Figure 13-5 Removing Taping Heads From Case Sealer International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 35...
15.4 Copies of Test Reports, Certifications (etc.) Required by User Electrical tests 1 - Earth continuity 2 - Insulation resistance 3 - High voltage test Reference; EN60204-1 par. 20.2.,3.,4. International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 37 44-0009-2161-7 / ECO# 0078483...
16. Technical Documentation and Information 16.1 Electric Diagram: 220V, 50Hz, 1 Ph (continued on next page) International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 38 44-0009-2161-7 / ECO# 0078483...
Page 51
16. Technical Documentation and Information 16.1 Electric Diagram: 400V, 50Hz, 3 Ph (continued) International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 39 44-0009-2161-7 / ECO# 0078483...
Page 52
78-8076-4726-4 • Figure Number contained in this kit is also available • Position as a replacement stock item. • 3M Part Number (11 Digits) • Description • Quantity Replacement Parts Ordering Information Refer to Manual 2 or 3 for recom- and Service mended taping head spare parts.
Page 53
Important – Not all the parts listed are normally stocked items. Some parts or assemblies shown are available only on special order. Contact 3M/Tape Dispenser Parts to confirm item availability International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™...
Page 54
International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 42 44-0009-2161-7 / ECO# 0078483...
Page 58
Note: Part Number 19 - 3” Taping Head only Note: See Parts List for Accuglide 2” and 3” information Figure 15967 International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 46 44-0009-2161-7 / ECO# 0078483...
Page 68
8000a-I / 8000a3-I 54 28 Left Side is Shown (Right Side - See Parts List) Figure 16090 International - ENG 3M-Matic 8000a-I / 8000a3-I - Type 11700 ™ February 2021 Page 56 44-0009-2161-7 / ECO# 0078483...
Instructions and Parts List 3M-Matic ™ Accuglide ™ Upper and Lower High Speed Taping Heads 2 Inch Type 10800 Serial #: For reference, record machine serial number here. Important Safety Information BEFORE INSTALLING OR OPERATING THIS EQUIPMENT Read, understand and follow all safety and operating instructions.
Page 78
International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page ii Source Document for all related Manuals/Translations 44-0009-2070-0 / ECO#0078483...
Page 79
Included with each machine is an Instructions and Parts List manual. Technical Assistance/Replacement Parts and Additional Manuals: Call 3M-Matic™ Help line. Provide the customer support coordinator with the model/ machine name, machine type, and serial number that are located on the identification plate (For example: Accuglide 3 - 2 inch - Type 10800 - Serial Number 13282).
Page 80
International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page iv Source Document for all related Manuals/Translations 44-0009-2070-0 / ECO#0078483...
Page 81
Replacement Parts and Service Information (continued) To Our Customers: This is the 3M-Matic /AccuGlide /Scotch equipment you ordered. It has been set ™ ™ ® up and tested in the factory with Scotch tapes. If any problems occur when operating ®...
Page 82
International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page vi Source Document for all related Manuals/Translations 44-0009-2070-0 / ECO#0078483...
Page 83
Replacement Parts and Service ......19-20 Replacement Parts Illustrations and Parts List ..21-End of Manual International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™...
Page 84
Buyer shall indemnify and hold Seller harmless against any claim by third parties resulting from failure to comply with the aforesaid laws and standards. AccuGlide , Scotch , and 3M-Matic are Trademarks of 3M, St. Paul, Minnesota 55144-1000 ™ ™ ™ International - ENG...
® seam of regular slotted containers. These taping heads are incorporated into most standard 3M-Matic™ case sealers. The compact size and simplicity of the taping head also makes it suitable for mounting in box conveying systems other than 3M-Matic™ case sealers. This includes replacement of other types of taping, gluing or stapling heads in existing case sealing machines.
Page 86
International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 2 Source Document for all related Manuals/Translations 44-0009-2070-0 / ECO#0078483...
3M Closure and Masking Systems Division 3M Center, St. Paul, MN 55144-1000 (USA) Edition 2021/Copyright 3M 2021. All rights reserved The manufacturer reserves the right to change the product at any time without notice. How to use this Manual The manual is an important part of the machine; all information contained herein is intended to enable the equipment to be maintained in perfect condition and operated safely.
The blades are extremely sharp. system is running (Important Safeguards continued on next page) International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021...
Page 89
See "Replacement Parts Illustrations and Parts Lists" for label part numbers. Upper Taping Head Label 78-8137-3317-3 Lower Taping Head Label 78-8137-3316-5 78-8070-1335-0 Figure 1-1 Replacement Labels/3M Part Numbers International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™...
5. Box Size Capacities: For use with center seam regular slotted containers. When upper and lower taping heads are used on “3M-Matic” case sealers, refer to the respective instruction manual specifications for box weight and size capacities. 6. Operating Rate: Conveyor speeds up to 0.5 m/s [100 feet per minute].
* This dimension can be reduced to 90mm [3.5 in.] when both heads are converted to 50mm [2 in.] tape leg lengths. Figure 2-1 Dimensional Drawing International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021...
Taping Head is supplied with a buffing the transportation company and also arm guard. Adjustments to guard may notify your 3M Representative. be required to install taping head into some older design case sealers. Installation Guidelines 4.
Tape Adhesive Side Tape Supply Roll Tape Drum Figure 3-2 Taping Head Components/Threading Diagram - Lower Head International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 9 Source Document for all related Manuals/Translations...
2. Lower taping head is loaded and Figure 3-3 Tape Loading/Threading threaded in same manner as upper head. International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 10...
Page 95
Excess tape can be cut with a scissors at applying roller. Figure 3-4 Tape Loading/Threading Figure 3-5 Tape Loading/Threading International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 11...
Should tape adhesive build-up occur on blade, carefully wipe clean with an oily cloth. (Maintenance continued on next page.) International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 12...
Figure 4-2 Roller Shaft Section View this socket after removing one screw to hold the shaft for removal of the second screw (See Figure 4-2). International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021...
- Never attempt to work on the taping head or load tape while the box drive system is running (adjustments continued on next page.) International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021...
Figure 5-5 One-Way Tension Roller - Never attempt to work on the taping head or load tape while the box (Adjustments continued on next page.) International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021...
The blades are extremely sharp. system is running International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021...
If not, press bearing further into roller or replace roller. International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021...
Page 102
Centering guides not centered Adjust centering guides Box flaps not of equal length Check box specifications International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 18 Source Document for all related Manuals/Translations...
Spring – Torsion Replacement Parts and Service Refer to the first page of this instruction manual “Replacement Parts and Service Information". International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021...
Page 104
International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 20 Source Document for all related Manuals/Translations 44-0009-2070-0 / ECO#0078483...
Page 105
Information" for replacement parts ordering information. Important – Not all the parts listed are normally stocked items. Some parts or assemblies shown are available only on a special order basis. Contact 3M/Tape Dispenser Parts to confirm item availability. International - ENG 3M-Matic...
Page 106
International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 22 Source Document for all related Manuals/Translations 44-0009-2070-0 / ECO#0078483...
Page 107
Figure 10922 Figure 10919 Figure 10921 Figure 10920 Tape Head - AccuGlide ™ 3 - 2 inch International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 23 Source Document for all related Manuals/Translations...
Page 108
AccuGlide 3 - 2" ™ Figure 10925 – Upper Head International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 24 Source Document for all related Manuals/Translations 44-0009-2070-0 / ECO#0078483...
Page 110
AccuGlide 3 - 2" ™ Figure 10922 – Upper and Lower Heads International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 26 Source Document for all related Manuals/Translations 44-0009-2070-0 / ECO#0078483...
Page 112
AccuGlide 3 - 2" ™ Figure 10919 – Upper Head International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 28 Source Document for all related Manuals/Translations 44-0009-2070-0 / ECO#0078483...
Page 113
AccuGlide 3 - 2" ™ Figure 10919 – 2" Upper Head Ref. No. 3M Part No. Description 10919-1 78-8137-3300-9 Buffing Arm – Sub Assembly 10919-2 78-8137-3301-7 Buffing Arm – Sub Assembly 10919-3 78-8052-6575-4 Shaft – Roller 10919-4 78-8137-1398-5 Roller - Buffing Assembly 10919-5 78-8070-1220-4 Spacer – Spring 10919-6 78-8052-6580-4 Spacer 10919-7 26-1003-5829-5 Screw –...
Page 114
3 - 2" ™ Figure 10923 Upper and Lower Heads Figure 10923 – Upper and Lower Heads International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 30 Source Document for all related Manuals/Translations...
Page 115
AccuGlide 3 - 2" ™ Figure 10923 – 2" Upper and Lower Heads Ref. No. 3M Part No. Description 10923-1 78-8137-3302-5 Link – Assembly 10923-3 78-8137-3304-1 Shaft – Pivot, Buffing 10923-4 78-8017-9082-1 Bearing – Special 30 mm 10923-5 78-8017-9106-8 Screw – Bearing Shoulder...
Page 116
AccuGlide 3 - 2" ™ Figure 10921 – Upper and Lower Heads International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 32 Source Document for all related Manuals/Translations 44-0009-2070-0 / ECO#0078483...
Page 117
AccuGlide 3 - 2" ™ Figure 10921 – 2" Upper and Lower Heads Ref. No. 3M Part No. Description 10921-1 78-8137-3307-4 Frame – Cut-Off Weldment 10921-2 78-8017-9173-8 Blade – 65 mm/2.56 Inch 10921-3 26-1003-8596-7 Screw - Hex Hd M5 x 8 w/ Ext. Tooth Lockwasher...
Page 118
AccuGlide 3 - 2" ™ Figure 10401 – Upper and Lower Heads International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 34 Source Document for all related Manuals/Translations 44-0009-2070-0 / ECO#0078483...
Page 120
AccuGlide 3 - 2" ™ Figure 10924 – Lower Head International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 36 Source Document for all related Manuals/Translations 44-0009-2070-0 / ECO#0078483...
Page 122
AccuGlide 3 - 2" ™ Figure 10920 – Lower Head International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 38 Source Document for all related Manuals/Translations 44-0009-2070-0 / ECO#0078483...
Page 123
AccuGlide 3 - 2" ™ Figure 10920– Lower Head Ref. No. 3M Part No. Description 10920-1 78-8137-3300-9 Buffing Arm – Sub Assembly 10920-2 78-8137-3301-7 Buffing Arm – Sub Assembly 10920-3 78-8052-6575-4 Shaft – Roller 10920-4 78-8137-1398-5 Roller - Buffing Assembly 10920-5 78-8070-1220-4 Spacer – Spring 10920-6 78-8052-6580-4 Spacer 10920-7 26-1003-5829-5 Screw – Hex Hd, M6 x 12...
Page 124
International - ENG 3M-Matic Accuglide 3 - 2 Inch Taping Head - Type 10800 Original Instructions ™ February 2021 Page 40 Source Document for all related Manuals/Translations 44-0009-2070-0 / ECO#0078483...
Page 125
Instructions and Parts List 3M-Matic ™ Accuglide ™ Type 10800 Upper and Lower High Speed Taping Heads 3 Inch Serial #: For reference, record machine serial number here. Important Safety Information BEFORE INSTALLING OR OPERATING THIS EQUIPMENT Read, understand and follow all safety and operating instructions.
Page 126
International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page ii Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 127
Included with each machine is an Instructions and Parts List Manual. Technical Assistance/Replacement Parts and Additional Manuals: Call the 3M-Matic™ Help line. Provide the customer support coordinator with the model/ machine name, machine type, and serial number that are located on the identification plate (For example: Model - Accuglide 3 High Speed 3”...
Page 128
International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page iv Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 129
Replacement Parts and Service Information (continued) To Our Customers: This is the 3M-Matic /AccuGlide /Scotch equipment you ordered. It has been set ™ ™ ® up and tested in the factory with Scotch tapes. If any problems occur when operating ®...
Page 130
International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page vi Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 131
Replacement Parts and Service ......19-20 Replacement Parts Illustrations and Parts List ..21-End of Manual International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™...
Page 132
Buyer shall indemnify and hold Seller harmless against any claim by third parties resulting from failure to comply with the aforesaid laws and standards. International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions...
® seam of regular slotted containers. These taping heads are incorporated into most standard 3M-Matic™ case sealers. The compact size and simplicity of the taping head also makes it suitable for mounting in box conveying systems other than 3M-Matic™ case sealers. This includes replacement of other types of taping, gluing or stapling heads in existing case sealing machines.
Page 134
International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 2 Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 135
(ELV), a glossary with a definition of symbols, plus a parts list of the 3M-Matic™ Accugllide 3 (3 inch) 3M Closure and Masking Systems Division 3M Center St.
The blades are extremely sharp. system is running (Important Safeguards continued on next page) International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 4...
Page 137
See "Replacement Parts Illustrations and Parts Lists" for label part numbers. Upper Taping Head Label 78-8137-3317-3 Lower Taping Head Label 78-8137-3316-5 78-8070-1335-0 Figure 1-1 Replacement Labels/3M Part Numbers International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™...
90mm [3.5 inches] (with optional 2 inch leg length) Case Sealer Width – 150mm [6 inches] When upper and lower taping heads are used on “3M-Matic” case sealers, refer to the respective instruction manual specifications for box weight and size capacities.
* This dimension can be reduced to 90mm [3.5 in.] when both heads are converted to 50mm [2 in.] tape leg lengths. Figure 2-1 Dimensional Drawing International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021...
Taping Head is supplied with a buffing the transportation company and also arm guard. Adjustments to guard may notify your 3M Representative. be required to install taping head into some older design case sealers. Installation Guidelines 4.
Tension Roller Tape Adhesive Side Tape Supply Roll Tape Drum Figure 3-2 Taping Head Components/Threading Diagram - Lower Head (Left Side View) International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 9...
2. Lower taping head is loaded and Figure 3-3 Tape Loading/Threading threaded in same manner as upper head. International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 10...
Page 143
Excess tape can be cut with a scissors at applying roller. Figure 3-4 Tape Loading/Threading Figure 3-5 Tape Loading/Threading International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 11 Source Document for all related Manuals/Translations...
Silicone. Should tape adhesive build-up occur on blade, carefully wipe clean with an oily cloth. (Maintenance continued on next page.) International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 12 Source Document for all related Manuals/Translations...
Insert a 4mm hex key wrench into this socket after removing one screw to hold the shaft for removal of the second screw. See Figure 4-2. International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 13...
- Never attempt to work on the taping head or load tape while the box drive system is running (adjustments continued on next page.) International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021...
- Never attempt to work on the taping Figure 5-5 One-Way Tension Roller head or load tape while the box drive system is running (Adjustments continued on next page.) International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 15...
The blades are extremely sharp. system is running International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 16...
If not, press bearing further into roller or replace roller. International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 17...
Page 150
Centering guides not centered Adjust centering guides Box flaps not of equal length Check box specifications International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 18 Source Document for all related Manuals/Translations...
78-8113-7030-9 Spring – Torsion Replacement Parts and Service Refer to the first page of this instruction manual “Replacement Parts and Service Information". International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 19...
Page 152
International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 20 Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Information" for replacement parts ordering information. Important – Not all the parts listed are normally stocked items. Some parts or assemblies shown are available only on a special order basis. Contact 3M/Tape Dispenser Parts to confirm item availability. International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™...
Page 154
International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 22 Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 155
10929 Figure 10926 (Upper) Figure 10928 Figure 10927 (Lower) Assemblies - AccuGlide ™ 3 - 3 inch International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 23 Source Document for all related Manuals/Translations...
Page 156
AccuGlide 3 - 3” ™ Figure 10932 – Upper Head International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 24 Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 158
AccuGlide 3 - 3” ™ Figure 10929 – Upper and Lower Heads International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 26 Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 160
AccuGlide 3 - 3” ™ Figure 10926 – Upper Head International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 28 Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 161
AccuGlide 3 - 3” ™ Figure 10926 – Upper Head Ref. No. 3M Part No. Description 10926-1 78-8137-3300-9 Buffing Arm – Sub Assembly 10926-2 78-8137-3301-7 Buffing Arm – Sub Assembly 10926-3 78-8091-0799-4 Shaft – 10 x 85, W/Hexagon 10926-4 78-8137-1397-7 Roller – Buffing Assembly 10926-5 78-8076-4739-7 Spacer – Spring 10926-6 78-8052-6580-4...
Page 162
AccuGlide 3 - 3” ™ Figure 10930 – Upper and Lower Heads International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 30 Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 163
AccuGlide 3 - 3” ™ Figure 10930 – Upper and Lower Heads Ref. No. 3M Part No. Description 10930-1 78-8137-3302-5 Link – R/H Assembly 10930-3 78-8137-3314-0 Shaft – Pivot, Buffing 10930-4 78-8017-9082-1 Bearing – Special 30 mm 10930-5 78-8017-9106-8 Screw – Bearing Shoulder...
Page 164
AccuGlide 3 - 3” ™ Figure 10928 – Upper and Lower Heads International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 32 Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 166
AccuGlide 3 - 3” ™ Figure 10402 – Upper and Lower Heads International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 34 Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 167
AccuGlide 3 - 3” ™ Figure 10402 – 3" Latch Upper and Lower Heads Ref. No. 3M Part No. Description 10402-1 78-8070-1395-4 Bracket – Bushing Assembly 10402-2 78-8060-8462-6 Shaft – Tape Drum, 3 Inch Head 10402-3 78-8017-9169-6 Nut – M18 x 1...
Page 168
AccuGlide 3 - 3” ™ 17 19 Figure 10931 – Lower Head International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 36 Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 170
AccuGlide 3 - 3” ™ Figure 10927 – Lower Head International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 38 Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 171
AccuGlide 3 - 3” ™ Figure 10927 – Lower Head Ref. No. 3M Part No. Description 10927-1 78-8137-3300-9 Buffing Arm – Sub Assembly 10927-2 78-8137-3301-7 Buffing Arm – Sub Assembly 10927-3 78-8091-0799-4 Shaft – 10 x 85, W/Hexagon 10927-4 78-8137-1397-7 Roller – Buffing 10927-5 78-8076-4739-7 Spacer – Spring 10927-6 78-8052-6580-4...
Page 172
International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 40 Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 173
International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 41 Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...
Page 174
International - ENG 3M-Matic Accuglide 3 - 3 Inch Taping Head ™ Original Instructions February 2021 Page 42 Source Document for all related Manuals/Translations 44-0009-2071-8 / ECO# 0078045...