Advertisement
• For TA and TF type, the set temperature can be changed according to the 0 - 10 V input of AI3.
• In the set temperature with the remote controller and this control, the post-setting is prioritized.
• The set temperature can be changed only for cooling and heating operations.
• To use this control, set DN [4A9] = 1.
T TA type
10.00
Heating / Cooling
9.70
8.95
8.20
7.45
6.70
5.95
5.20
4.45
3.70
2.95
2.20
1.45
0.70
0.00
Terminal AO1 / AO1: FAN speed 0 - 10 V output
• Each FAN speed is output at 0 - 10 V.
• The ripple voltage of 0 - 10 V is less than ± 30 mV of the
set voltage. Connect equipment that is not affected by
this ripple voltage.
• The output voltage can be changed by DN setting [4A4]
to [4A6].
* Terminal AO2 / AO2 cannot be used.
CAUTION
The impedance of the device that receives the 0 - 10 V output signal shall be 10 kΩ or more.
40VAM--C8FATEE
(Terminal block without relay)
Shield wire MAX. 200 m
AO1
Output
0 - 10 V
AO1
Temperature Set Point
• When a wired remote controller is fitted the temperature set point can be changed, however this has no impact on the
demand, which is controlled by the 0 - 10 V Analog Input.
Set temp
(V)
29°C / 29°C
9.50
28°C / 28°C
8.75
27°C / 27°C
8.00
26°C / 26°C
7.25
25°C / 25°C
6.50
24°C / 24°C
5.75
23°C / 23°C
5.00
22°C / 22°C
4.25
21°C / 21°C
3.50
20°C / 20°C
2.75
19°C / 19°C
2.00
18°C / 18°C
1.25
18°C / 18°C
0.50
Locally procured
0 - 10 V Signal (+)
T TF type
10.00
9.70
8.95
8.20
7.45
6.70
5.95
5.20
4.45
3.70
2.95
2.20
1.45
0.70
0.00
FAN
Output
speed
(Def)
HH
9 V
4A4 (0009)
H
6 V
4A5 (0006)
L
2 V
4A6 (0002)
STOP
0 V
40VAMR-C8FATEE
(Terminal block with relay)
– 34 –
Set temp
Heating / Cooling
30°C / 25°C
29°C / 24°C
28°C / 23°C
27°C / 22°C
26°C / 21°C
25°C / 20°C
24°C / 19°C
23°C / 18°C
22°C / 17°C
21°C / 16°C
20°C / 15°C
19°C / 14°C
18°C / 13°C
Initial
Applicable range
(Def)
8 V (0008) - 10 V (0010)
4 V (0004) - 7 V (0007)
1 V (0001) - 3 V (0003)
-
-
Same as on the left
(V)
9.50
8.75
8.00
7.25
6.50
5.75
5.00
4.25
3.50
2.75
2.00
1.25
0.50
Advertisement
