Table of Contents
Advertisement
8.
Use the rotary selector to set the time to
four minutes.
9.
Press
to start.
a The appliance starts to heat and the time starts to
count down.
a Once the time has elapsed, an audible signal
sounds. A message appears in the status bar.
10.
Use
to switch the appliance off and leave the
cooking compartment to cool for approx.
20 minutes.
19.2 Wiping down the cooking compartment
ATTENTION!
The prolonged presence of moisture in the cooking
compartment leads to corrosion.
▶
After using the cleaning assistance, wipe the cook-
ing compartment and allow it to dry completely.
20 Descaling
To ensure that your appliance continues to operate cor-
rectly, it must be descaled regularly.
How frequently you need to run the descaling pro-
gramme will depend on the water hardness and how
many times you have used the steam function. The ap-
pliance indicates when only another five or fewer
steam-assisted operations are possible. If you do not
carry out the descaling, you can no longer set any op-
eration with steam.
Descaling comprises several steps and takes approx.
70–95 minutes:
¡ Descaling (approx. 55–70 minutes)
¡ First rinse cycle (approx. 9–12 minutes)
¡ Second rinse cycle (approx. 9–12 minutes)
For reasons of hygiene, the descaling programme must
be run in full.
If descaling is interrupted, you can no longer set any
operation. To ensure that the appliance is ready for op-
eration again, carry out two rinse cycles.
20.1 Preparing descaling
ATTENTION!
The length of time for which the descaler is left to work
is based on the recommended, liquid descaler. Other
descalers may damage the appliance.
▶
Only use the liquid descaler recommended by us
for the descaling programme.
If descaling solution comes into contact with the control
panel or other delicate surfaces, it will damage them.
▶
Remove descaling solution immediately with water.
1.
Mix the descaling solution:
200 ml liquid descaler
‒
400 ml water
‒
Requirement: The cooking compartment must have
cooled down.
1.
Open the appliance door and remove the remaining
water with an absorbent sponge cloth.
2.
Clean the smooth surfaces in the cooking compart-
ment with a dish cloth or a soft brush. Remove stub-
born food remnants using a stainless steel scouring
pad.
3.
Remove limescale with a cloth soaked in vinegar.
Then wipe with clean water and rub dry with a soft
cloth (including under the door seal).
4.
In order to dry the cooking compartment, leave the
appliance door open in the detent position (approx.
30°) for approx. one hour.
2.
Open the control panel.
3.
Remove the water tank and pour the descaling solu-
tion into it.
4.
Once the descaling solution has been poured into
the water tank, slide the tank back in.
5.
Close the control panel.
20.2 Setting the descaling function
Requirement: → "Preparing descaling", Page 27
1.
Press
.
2.
In the operating mode menu, select "Descaling".
a The duration appears in the display. The duration
cannot be changed.
3.
Press
to start.
a The descaling programme starts and the duration
counts down.
a Once the first part of the descaling programme has
finished, an audible signal sounds. The appliance
prompts you to rinse twice.
4.
To rinse the appliance, for each rinse cycle:
Open the control panel and remove the water
‒
tank.
Thoroughly rinse the water tank and fill it with
‒
fresh water.
Slide in the water tank and close the control
‒
panel.
Use
to start rinsing.
‒
a A signal sounds when each rinse cycle has ended.
5.
Once the second rinsing cycle is complete:
Empty and dry the water tank.
‒
→ "Emptying the water tank", Page 18
Press
to switch the appliance off
‒
a Descaling is complete and the appliance is ready
for use.
Descaling en
27
Advertisement
Table of Contents
