Table of Contents
Advertisement
en Descaling
19.2 Cleaning the cooking compartment
after using the cleaning aid
ATTENTION!
The prolonged presence of moisture in the cooking
compartment leads to corrosion.
After using the cleaning assistance, wipe the cook-
▶
ing compartment and allow it to dry completely.
Allow the appliance to cool down.
1.
2.
Wipe out the remaining water in the cooking com-
partment using an absorbent sponge cloth.
Descaling
20 Descaling
To ensure that your appliance continues to operate cor-
rectly, it must be descaled regularly.
How frequently you need to run the descaling pro-
gramme depends on the water hardness and how
many times you have used the steam-assisted opera-
tions. The appliance indicates when only another 5 or
fewer steam-assisted operations are possible. If you do
not carry out descaling, you can no longer set any op-
eration with steam.
Descaling comprises several steps and takes
approximately 70 - 95 minutes:
¡ Descaling (approx. 55 - 70 minutes)
¡ First rinse cycle (approx. 8 - 12 minutes)
¡ Second rinse cycle (approx. 8 - 12 minutes)
Carry out descaling in full.
If descaling is interrupted, you can no longer set any
operation. To ensure that the appliance is ready for op-
eration again, carry out 2 rinse cycles.
20.1 Preparing descaling
ATTENTION!
The length of time for which the descaler is left to work
is based on the recommended, liquid descaler. Other
descalers may damage the appliance.
Only use the liquid descaler recommended by us
▶
for the descaling programme.
If descaling solution comes into contact with the control
panel or other delicate surfaces, it will damage them.
Remove descaling solution immediately with water.
▶
Mix the descaling solution:
1.
200 ml liquid descaler
‒
400 ml water
‒
Open the control panel.
2.
Drying function
21 Drying function
To prevent residual moisture , dry the cooking compart-
ment following operation with steam.
30
Clean the smooth enamel surfaces in the cooking
3.
compartment with a dish cloth or a soft brush. Re-
move stubborn food remnants using a stainless
steel scouring pad.
4.
Remove limescale with a cloth soaked in vinegar,
and wipe this away with clean water.
Dry the cooking compartment with a soft cloth.
5.
6.
To dry the cooking compartment completely, leave
the appliance door open for approx. 1 hour or use
the "Drying" function.
→ "Setting the drying process", Page 31
Remove the water tank and fill it with descaling solu-
3.
tion.
Once the descaling solution has been poured into
4.
the water tank, slide the tank back in.
5.
Close the control panel.
20.2 Setting the descaling programme
Requirement: → "Preparing descaling", Page 30
Press "Cleaning".
1.
Press "Descaling".
2.
The duration cannot be changed.
Press
.
3.
a A message stating that you should carry out the ne-
cessary preparatory work for descaling appears on
the display.
4.
Confirm the message.
a The descaling programme starts and the duration
counts down.
a Once the first part of the descaling programme has
finished, a signal sounds. The appliance prompts
you to carry out 2 rinse cycles.
To rinse the appliance, for each rinse cycle:
5.
Open the control panel and remove the water
‒
tank.
Thoroughly rinse the water tank and fill it with
‒
fresh water.
Slide in the water tank and close the control
‒
panel.
Press
to start the rinse cycle.
‒
a A signal tone sounds when each rinse cycle has
ended.
Once the second rinse cycle is complete:
6.
Empty and dry the water tank.
‒
→ "Emptying the water tank", Page 19
Press
to switch the appliance off.
‒
ATTENTION!
If there is water on the cooking compartment floor
when operating the appliance at temperatures above
120 °C, this will damage the enamel.
Do not use the appliance if there is water on the
▶
cooking compartment floor.
Wipe away any water on the cooking compartment
▶
floor before operation.
Advertisement
Table of Contents
