Technical Data; Double Insulation; Commissioning And Use - Narex EVP 13 E-2H3 Original Operating Manual

Technical data

Drilling machine and impact drill
Type
Supply.voltage.
Power.frequency.
Power.input.
Speed.under.load
. 1st.speed.gear.
. nd.speed.gear.
Idle.speed
. 1st.speed.gear.
. nd.speed.gear.
Number.of..impacts
. 1st.speed.gear.
. nd.speed.gear.
Speed.pre-selection
Right-left.turning
Extent.of.chuck.ø.
Thread.on.spindle.
Inner.hexagon.in.spindle.
Drilling.ø.max
. into.steel.
. into.aluminium.
. into.wood.
. into.concrete.
Clamping.neck.ø.
Weight.
Protection.class.
Controls
1 ............ Chuck with ring gear
2 ............ Spots on spindle
3 ............ Clamping neck
4 ............ Lever for impact shifting
5 ............ Air vents
6 ............ Stop bar
7 ............ Additional handle
8 ............ Gear-shifting lever (EV 13 E-2H3, EVP 13 E-2H3)
9 ............ Alteration switch lever (EVP 13 E-2H3)
10 . ......... Speed pre-selection wheel
11 . ......... Switch / controller
12 . ......... Latching pin
13 . ......... Screw shaft
14 . ......... Spindle cover
15 . ......... Drilling spindle
16 . ......... Chuck hook
17 . ......... Spanner
18 . ......... Socket screw wrench
19 . ......... Quick-tightening chuck
The displayed or described accessories need not be included in the delivery
package.

Double insulation

To ensure maximum safety of the user, our tools are designed and built to
satisfy applicable European standards (EN standards). Tools with double
insulation are marked by the international symbol of a double square. These
tools must not be grounded and a two-wire cable is sufficient to supply them
with power. Tools are shielded in accordance with EN 50114.
Use
The machine is intended drilling in wood, metal, ceramic and plastic. Machines
with electronic control and right/left rotation are also suitable for screwing
and thread cutting ( Only for soft screwdriving applications).
EVP 13 E-2H3:
The machine is intended for impact drilling in brick, concrete and stone as
well as for drilling in wood, metal, ceramics and plastics. Machines with
electronic control and right/left rotation are also suitable for screwing and
thread-cutting.
The user alone is responsible for any liabilities caused by usage other than
intended.
EV 13 F-H3
30.V.
50–60.Hz.
650.W.
0–.75.min .
-1
û.
0–4.000.min .
-1
û.
û.
û.
1,5–13.mm.
1/"–0.UNF.
û.
13.mm.
16.mm.
5.mm.
û.
43.mm.
1,5.kg.
II./.
Any unauthorised use might cause damage to the tool. Therefore follow
these instructions:
Check whether the data on the name plate correspond with the actual
power supply voltage. Tools designed for 230 V may be connected also
to 220 / 240 V.
Additional handle
For safety reasons always use the additional handle (7), firmly mounted on the
clamping neck (3). The stop bar (6) can be used to adjust the drilling depth.
Clamping a drill
Insert tool and tighten equally in all 3 holes with chuck key.
Switching on and off
By pressing the switch button (11) the machine activates and releasing the
button stops it.
Permanent run
By pressing the switch button (11) to the stop and simultaneous pressing
the latching pin (12) permanent run is achieved.
Repeated pressing the switch button (11) and its release the permanent run
is discontinued.
Speed control
By light and gradual pressing the controller button (11) you will achieve low
speed and controlled continuous run-up.
By further gradual pressing the button the speed increases to the
pre-selected speed.
Electronic speed pre-selection
Using the pre-selection wheel (10) the required pre-selected speed is set–
even if the machine runs. The necessary speed depends on the type of the
material drilled, and a practical test is recommended to verify it.
If the machine is loaded considerably, adjust the pre-selection wheel (10) to
the marginal position in the + direction (max speed – control disconnected).
EV 13 E-2H3
30.
50–60.
650.
0–630.min .
-1
0–1.730.min .
-1
0–1.100.min .
-1
0–3.000.min .
-1
û.
û.
1,5–13.mm.
1/"–0.UNF.
1/4".
13.mm.
16.mm.
35.mm.
û.
43.mm.
1,7.kg.
II./.

Commissioning and use

- Always use sharp drill bits.
- Load the tool to avoid any significant reduction of speed or stoppage.
- Always change the speed gear when the machine is idle or at the
machine slow-down at low speed, in no case during the drilling or
when the machine is otherwise loaded.
English
EVP 13 E-2H3
30
50–60
650
0–630.min
-1
0–1.730.min
-1
0–1.100.min
-1
0–3.000.min
-1
0–1.600.min
-1
0–34.600.min
-1
1,5–13.mm
1/"–0.UNF
1/4"
13.mm
16.mm
35.mm
16.mm
43.mm
1,8.kg
II./
13