User Manual (Ver. 1.0) - Table of Contents GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Table of Contents Table of Contents About Technical Note Notice/Warranty Notice Warranty Certifications CE Compliance Warning Supplement Supplement Usage Precautions Notes on Cable Configurations Notes on Attaching the Lens...
Page 3
User Manual (Ver. 1.0) - Table of Contents GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 ② Direct Mounting (or Use MP-43 Tripod Adapter Plate) ③ Camera Link Cable ④ Frame Grabber Board ⑤ DC IN Connection Cable (Option, EV and UV Models Only) ⑥...
Page 4
User Manual (Ver. 1.0) - Table of Contents GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 1x8-1Y (FVAL, DVAL, V-Offset, Exposure Time) 1x4-1Y (FVAL, DVAL, V-Offset, Exposure Time) 1x3-1Y (FVAL, DVAL, V-Offset, Exposure Time) 1x2-1Y (FVAL, DVAL, V-Offset, Exposure Time) 1x8-1Y (Frame Period, Exposure Time, Exposure End to FVAL Active Start)
Revision History About Technical Note Some additional technical information is provided on the JAI website as Technical Notes. In this manual, if a technical note is available for a particular topic, the above icon is shown. Please refer to the following URL for Technical notes.
The material contained in this manual consists of information that is proprietary to JAI Ltd., Japan, and may only be used by the purchasers of the product. JAI Ltd., Japan makes no warranty for the use of its product and assumes no responsibility for any errors which may appear or for damages resulting from the use of the information contained herein.
User Manual (Ver. 1.0) - Notice/Warranty GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Warning Changes or modifications to this unit not expressly approved by the party responsible for FCC compliance could void the user’s authority to operate the equipment.
User Manual (Ver. 1.0) - Notice/Warranty GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Supplement The following statement is related to the regulation on “Measures for the Administration of the Control of Pollution by Electronic Information Products “, known as “China RoHS“. The table shows contained Hazardous Substances in this camera.
User Manual (Ver. 1.0) - Notice/Warranty GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Supplement The following statement is related to the regulation on “Measures for the Administration of the Control of Pollution by Electronic Information Products “, known as “China RoHS“. The table shows contained Hazardous Substances in this camera.
User Manual (Ver. 1.0) - Usage Precautions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Usage Precautions Notes on Cable Configurations The presence of lighting equipment and television receivers nearby may result in video noise. In such cases, change the cable configurations or placement.
User Manual (Ver. 1.0) - Usage Precautions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Phenomena Specific to CMOS Image Sensors The following phenomena are known to occur on cameras equipped with CMOS image sensors. These do not indicate malfunctions. Aliasing: When shooting straight lines, stripes, and similar patterns, vertical aliasing (zigzag distortion) may appear on the monitor.
GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Features GO-5000M-PMCL-1, GO-5000M-PMCL-EP-1 and GO-5000M-PMCL-UV-1 are small-in-size cameras providing both high resolution and a high frame rate with excellent image quality for machine vision applications. They are monochrome progressive scan COMS cameras equipped with CMOS sensors offering a 1-inch image format, a resolution of 5 million pixels, and a 5:4 aspect ratio.
User Manual (Ver. 1.0) - Parts Identification GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Parts Identification ① Lens Mount (C-Mount) ② POWER/TRIG LED ③ ④ Camera Link Connector 1 and 2 ⑤ Mounting Holes (M3, 3mm depth) ⑥ DC IN Connector (UV Model Only) ①...
User Manual (Ver. 1.0) - Parts Identification GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 ② POWER/TRIG LED Indicates the power or trigger input status. Status Lit amber Camera initializing. The light goes off after initiating Lit green Camera in operation in Continuous mode During operation in trigger mode, trigger signals are being input.
User Manual (Ver. 1.0) - Parts Identification GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Camera Link Connector 2 Input Signal Description Output 1, 26 Shield 2 (-), 15 (+) Y_OUT0 Data out 3 (-), 16 (+) Y_OUT1 Data out 4 (-), 17 (+)
User Manual (Ver. 1.0) - Parts Identification GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 ⑥ DC IN Connector (UV Model Only) Note: This connector is available only on the EP and UV camera. Connect the cable for DC IN here. Compatible Connectors...
User Manual (Ver. 1.0) - Preparation GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Preparation Read this section to learn how the camera connects to devices and accessories. The preparation process is described below. Step 1: Connect Devices Connect the lens, Camera Link cable, AC adapter, computer, and other devices.
User Manual (Ver. 1.0) - Preparation GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Step 1: Connect Devices ① Lens ② Direct Mounting (or Use MP-43 Tripod Adapter Plate) ③ Camera Link Cable ④ Frame Grabber Board ⑤ DC IN Connection Cable (Option, EV and UV Models Only) ⑥...
User Manual (Ver. 1.0) - Preparation GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 ① Lens C-mount lenses with lens mount protrusions of 10 mm or less can be attached. To prevent vignetting and to obtain the optimal resolution, use a lens that will cover the image sensor size.
User Manual (Ver. 1.0) - Preparation GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 ③ Camera Link Cable Connect the Camera Link cable to the Mini Camera Link connector. Use a cable that supports the Camera Link standard and is compatible with Mini Camera Link (SDR) connectors.
User Manual (Ver. 1.0) - Preparation GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Step 2: Verify Camera Operation When power is supplied to the camera while the necessary equipment is connected, the POWER/TRIG LED at the rear of the camera lights amber, and initialization of the camera starts.
Start Bit: 1bit Stop Bit: 1 bit Parity: None Xon/Xoff Control: None 2. Enter the command DVN? <CR><LF> from the terminal emulator software. If correctly connected, response DVN = JAI Ltd., Japan will be displayed. Item Short ASCII Command Description DVN? <CR><LF>...
User Manual (Ver. 1.0) - Preparation GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Step 4: Change the Camera Settings Related Setting Items: Image Format Control This section explains how to change settings by describing the procedure for changing the output format as an example.
User Manual (Ver. 1.0) - Preparation GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Example: Change the PixelFormat setting (ImageFormatControl) 1. To check the current PixelFormat setting, enter the command BA?<CR><LF> from the terminal emulator software. 2. To change the PixelFormat setting to Mono10, enter BA=1<CR><LF>.
User Manual (Ver. 1.0) - Preparation GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Adjust the Black Level The black level can be set in the following range. Short ASCII Item Values Command BlackLevelRawAll -256 ~ 255. Step 6: Save the Settings Related Setting Items: User Set Control The configured setting values will be deleted when the camera is turned off.
User Manual (Ver. 1.0) - Preparation GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Save the User Settings 1. Stop image acquisition. Settings can only be saved when image acquisition on the camera is stopped. 2. Specify the storage location (UserSet1 - UserSet3) using the UserSetSave command and save the current camera settings.
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Main Functions This chapter describes the camera's main functions. Camera Link Interface Digital I/O 1 Camera Link Configuration Base Base Medium Full 80bit Camera Link port/bit 2Tap / 12bit...
Page 28
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Digital I/O 2 (1/2) Camera Link Configuration Base Base Medium Full 80bit Camera Link port/bit 2Tap / 12bit 3Tap/8bit 4Tap / 12bit 8 Tap / 8bit 8 Tap / 10bit...
Page 29
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Digital I/O 2 (2/2) Camera Link Configuration Base Base Medium Full 80bit Camera Link port/bit 2Tap / 12bit 3Tap/8bit 4Tap / 12bit 8 Tap / 8bit 8 Tap / 10bit...
Page 30
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 3. If you use 80-bit (8-tap/10-bit) camera configuration, DVAL and Exposure Active (JAI custom) are not output through the Camera Link interface. FVAL is only output via Digital I/O-1 connector.
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Digital IN/OUT Interface Related Setting Items: JAI Custom On this camera, the software control tool can assign the necessary signals used in the system to digital inputs and outputs.
Page 32
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Line Mode Indicates the status of the item selected in Line Selector. (INPUT or OUTPUT) Line Inverter Inverts the signal polarity for the item selected in Line Selector. (False=Positive, True=Negative)
Page 33
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Basic Block Diagram - 33 -...
Page 34
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 GPIO IN/OUT Matrix Trigger Selector Line Selector Pulse Generator Selector Trigger Source NAND 1 In 1 NAND 1 In 2 NAND 2 In 1 NAND 2 In 2...
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Pulse Generator Related Setting Items: JAI Custom Tips for using the Pulse Generator This camera has a frequency divider using the sensor clock as the basic clock and one pulse generator.
Page 36
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Pulse Generator Selector This is where you select a pulse generator. On this camera, it is fixed to Pulse Generator 0. Pulse Generator setting / Pulse Generator pulse construction...
Page 37
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Pulse Generator Clear Activation Set the clear conditions of clear count pulse for the pulse generator. Pulse Generator Clear Sync Mode Set the count clear method for the pulse generator. In case of Async Mode, if the clear signal is input during the length setting value, the counter will stop counting according to the clear signal input.
Page 38
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Pulse Generator Clear Source The following clear source can be selected as the pulse generator clear signal. Pulse Generator Description Clear Source Item Connect Low level signal to Clear Source for the pulse generator. Default setting High Connect High level signal to Clear Source for the pulse generator.
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Camera Output Format (Tap Geometry) Camera Output Format Bit Assignment 1X2–1Y 8-bit, 10-bit, 12-bit 1X3-1Y 8-bit 1X4–1Y 8-bit, 10-bit, 12-bit 1X8–1Y 8-bit, 10-bit Note: The camera output description is based on GenICam SFNC Ver.1.5.1.
Page 41
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 1X3-1Y 1X3–1Y is a 3-tap readout system specified in GenICam Tap Geometry. - 41 -...
Page 42
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 1X4–1Y 1X4–1Y is a 4-tap readout system specified in GenICam Tap Geometry. - 42 -...
Page 43
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 1X8–1Y 1X8–1Y is an 8-tap readout system and outputs as follows. - 43 -...
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Output Timing (Horizontal) The horizontal frequency is changed by setting the Tap Geometry. Horizontal timing per 1 tap in Camera Link output - 44 -...
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 1x8-1Y (LVAL Active/Non-Active, H Total) Horizontal Timing (Continuous Trigger Mode) (1/2) Camera Settings LVAL LVAL Binning H Total Active Camera Link Pixel Active Geometry Clock (Unit (Unit (Unit Width...
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 1x4-1Y (LVAL Active/Non-Active, H Total) Horizontal Timing (Continuous Trigger Mode) (1/2) Camera Settings LVAL LVAL Binning H Total Active Camera Link Pixel Active Geometry Clock (Unit (Unit (Unit Width...
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 1x3-1Y (LVAL Active/Non-Active, H Total) Horizontal Timing (Continuous Trigger Mode) (1/2) Camera Settings LVAL LVAL Binning H Total Active Camera Link Pixel Active Geometry Clock (Unit (Unit (Unit Width...
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 1x2-1Y (LVAL Active/Non-Active, H Total) Horizontal Timing (Continuous Trigger Mode) (1/2) Camera Settings LVAL LVAL Binning H Total Active Camera Link Pixel Active Geometry Clock (Unit (Unit (Unit Width...
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 1x8-1Y (1 Line Clock, Horizontal Frequency/Period) Horizontal Timing (Continuous Trigger Mode) (2/2) Note: A: Operation Value; B = Calculation Value Camera Settings A: Operation value B: Calculation value Binning...
Page 50
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Camera Settings A: Operation value B: Calculation value Binning 1 line Total Horizontal Horizontal Camera Link clock (Unit: Frequency (Unit: Period (Unit: Offset Offset Geometry Pixel Clock Width...
Page 51
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Camera Settings A: Operation value B: Calculation value Binning 1 line Total Horizontal Horizontal Camera Link clock (Unit: Frequency (Unit: Period (Unit: Offset Offset Geometry Pixel Clock Width...
Page 52
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Camera Settings A: Operation value B: Calculation value Binning 1 line Total Horizontal Horizontal Camera Link clock (Unit: Frequency (Unit: Period (Unit: Offset Offset Geometry Pixel Clock Width...
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 1x4-1Y (1 Line Clock, Horizontal Frequency/Period) Horizontal Timing (Continuous Trigger Mode) (2/2) Note: A: Operation Value; B = Calculation Value Camera Settings A: Operation value B: Calculation value Binning...
Page 54
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Camera Settings A: Operation value B: Calculation value Binning 1 line Total Horizontal Horizontal Camera Link clock (Unit: Frequency (Unit: Period (Unit: Offset Offset Geometry Pixel Clock Width...
Page 55
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Camera Settings A: Operation value B: Calculation value Binning 1 line Total Horizontal Horizontal Camera Link clock (Unit: Frequency (Unit: Period (Unit: Offset Offset Geometry Pixel Clock Width...
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 1x2-1Y (1 Line Clock, Horizontal Frequency/Period) Horizontal Timing (Continuous Trigger Mode) (2/2) Note: A: Operation Value; B = Calculation Value Camera Settings A: Operation value B: Calculation value Binning...
Page 58
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Camera Settings A: Operation value B: Calculation value Binning Camera Link 1 line Total Horizontal Horizontal Offset Offset Geometry Pixel Clock clock (Unit: Frequency (Unit: Period (Unit: Width...
Page 59
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Camera Settings A: Operation value B: Calculation value Binning Camera Link 1 line Total Horizontal Horizontal Offset Offset Geometry Pixel Clock clock (Unit: Frequency (Unit: Period (Unit: Width...
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Output Timing (Vertical) The below figure shows the vertical timing of Camera Link output during continuous trigger operation. However, with 1X8-1Y 10-bit geometry, which is 80-bit configuration, DVAL and Exposure Active, which are normally output to Camera Link spare bits, are not output through the Camera Link interface as data bits are applied to those bits.
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 1x8-1Y (Frame Period, Exposure Time, Exposure End to FVAL Active Start) Vertical Timing (Continuous Trigger Mode) (2/2) Camera Settings Exposure Binning Frame Frame Exposure End to Pixel Period...
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 1x4-1Y (Frame Period, Exposure Time, Exposure End to FVAL Active Start) Vertical Timing (Continuous Trigger Mode) (2/2) Camera Settings Exposure Binning Frame Exposure End to Frame Pixel Period...
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 1x3-1Y (Frame Period, Exposure Time, Exposure End to FVAL Active Start) Vertical Timing (Continuous Trigger Mode) (2/2) Camera Settings Exposure Binning Frame Exposure End to Frame Pixel Period...
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 1x2-1Y (Frame Period, Exposure Time, Exposure End to FVAL Active Start) Vertical Timing (Continuous Trigger Mode) (2/2) Camera Settings Exposure Binning Frame Exposure End to Frame Pixel Period...
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 ROI (Region of Interest) Settings Related Setting Items: Image Format Control On this camera, a subset of the image can be output by setting Width, Height, Offset- X, and Offset-Y.
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Acquisition Control With Trigger OFF (free running mode), the default frame rate of the camera is based on the specified ROI. The smaller the ROI, the faster the default frame rate. However, it is possible to specify a free- running frame rate (i.e., no trigger needed) that is slower than the default rate.
Page 72
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Refer to the Width value on the below table. Refer to the Height value on the below table. Figures for A to E by the Tap Geometry CL Clock Max.
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Exposure Settings Related Setting Items: Acquisition Control, JAI Custom This section describes how to set the exposure settings. Command Name Parameter Description Shutter control is not available. The exposure time depends on the frame rate.
Page 74
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 If Exposure Mode is set at Timed, the exposure operation can be selected as follows by setting Trigger Option. Trigger Option Setting Exposure Operation Timed (EPS) mode RCT mode If the trigger is used, it uses “Frame Start”.
Page 75
Note: Noise may make image unusable after 1 second. ExposureAuto This is a function to control the exposure automatically. It is effective only for Timed. JAI ALC Reference controls the brightness. There are two modes, OFF and Continuous. OFF: No exposure control Continuous: Exposure continues to be adjusted automatically In this mode, the following settings are available.
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Trigger Control The following 5 types of Trigger Control are available by the combination of Trigger Selector, Trigger Mode, Exposure Mode and Trigger Option. Camera Settings JAI Custom Trigger...
Page 77
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Trigger Source Select the trigger source to be used for trigger operation (Frame Start) from the following: Trigger Source Description Item Connect LOW level signal to the selected trigger operation (Default setting)
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Normal Continuous Operation This is used for applications which do not require triggering. Minimum interval (1X8–1Y, 8-bit, CL Clock =72.85MHz) Trigger Mode Readout Mode Time (Min. Frame Period)
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Timed Mode This mode captures image(s) with a preset exposure time by using the external trigger. An additional setting determines if the trigger pulse can be accepted during the exposure period.
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Trigger Width Mode In this mode, the exposure time is equal to the trigger pulse width. Accordingly, longer exposure times are supported. Additional settings determine if the trigger pulse can be accepted during the exposure period.
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 RCT Mode Related Setting Items: JAI Custom Until the trigger is input, the camera operates continuously and can use auto-gain, if necessary, to control the exposure setting. During this time, FVAL and LVAL are output but DVAL is not output.
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 RCT Mode Together with ALC Function The RCT mode can be used in conjunction with the ALC control so that the exposure is always set to the appropriate state when the trigger pulse is input. In this case, the following settings are additionally required to RCT mode settings.
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Sequence Mode Related Setting Items: JAI Custom This is a function to capture images in sequence based on preset ROI, Exposure Time, Gain and other parameters in the sequence index table. To use sequence mode, configure VideoSendMode (Trigger Sequence or Command Sequence).
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Trigger Sequence Mode Timing The following drawing shows the sequence mode timing concept. In this mode, it is not possible to overlap the next exposure while the previous trigger operation (Index table) is in progress.
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Descriptions of Index Table Parameters Sequence Mode Command Command Parameter Description Sequence ROI Index Index 1 ~ 128 Select an index to be set <Set to each Index>...
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Multi ROI Function Related Setting Items: JAI Custom This function divides one frame image into a maximum of 5 images vertically and reads out all areas in one frame. In this function, width is the same for all 5 images. In the GO-5000M-PMCLUV, image overlapping is not possible.
Page 87
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 ROI setting explanation if Multi ROI Index Max is set to 4 Video output of Multi ROI Note: In this mode, the frame grabber board must set its horizontal pixel number to Multi ROI Width and its vertical pixels to Multi ROI Max and the sum of Multi ROI Height.
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Operation and Function Matrix Vide Send Mode Exposure Trigger Trigger Binning Binning Exposure Auto Auto Over lap Sequence Operation Mode Option Vertical Horizontal Time Gain Exposure Multi ROI ✓...
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Gain Control Related Setting Items: Analog Control On this camera, the gain control uses Analog Base Gain and Digital Gain. Analog Base Gain can be set at 0dB, +6dB or +12dB. The digital gain is used for the master gain setting.
Page 90
The range for adjustment: Gain Raw Digital All: 100 ~ 1600 (0dB ~ 24dB) This provides automatic control of the gain level. Gain Auto This provides automatic control of the gain level. This is controlled by the command JAI ALC Reference. OFF: Adjust manually.
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 LUT (Lookup Table) Related Setting Items: LUT Control This function can be used to convert the input to the desired output characteristics. The Lookup Table (LUT) has 32 points for setup on this camera. The output level is created by applying gain to the input level to achieve the specified output level.
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Gamma Note: JAI Custom This command is used to set gamma 0.45, gamma 0.6 and gamma 1.0 (OFF) in 3 steps. The gamma value is an approximate value.
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Shading Correction Related Setting Items: JAI Custom This function compensates for shading (non-uniformity) caused by the lens or the light source used. This compensation can be performed even if shading issues are not symmetrical in horizontal and/or vertical directions.
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 ALC (Automatic Level Control) Related Setting Items: JAI Custom On this camera, auto gain and auto exposure can be combined to provide a wide ranging automatic exposure control from dark to bright or vice versa. The functions are applied in the sequence shown below and if one function is disabled, the remaining function will work independently.
User Manual (Ver. 1.0) - Main Functions GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 HDR (High Dynamic Range) HDR sensing mode can be set when HDR Mode is set to ON while Exposure Mode is Timed. The parameters to configure dynamic range are HDR_SLOPE Level 1, Level 2, Level 3 and Level 4.
User Manual (Ver. 1.0) - Short ASCII Command List GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Short ASCII Command List This chapter describes the communication control protocol based on the short ASCII command as the reference. Communication Setting Baud Rate: 9600 (Default)
User Manual (Ver. 1.0) - Short ASCII Command List GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Switching baud rate between PC and camera Camera always starts up with 9600bps. This can be switched to higher baud rates after a communication has been established. When switching to other baud rate the procedure is as follows.
User Manual (Ver. 1.0) - Short ASCII Command List GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Technology Specific Bootstrap Register Related Topic: Short ASCII Command List Short Name Access Values MIN MAX Default Description ASCII Indicate Support/Non- support status for each baud rate...
User Manual (Ver. 1.0) - Short ASCII Command List GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Image Format Control Related Topic: Configure the Output Format Name Access Short ASCII Values Default Description HTL=[Param.]<CR>< LF> Height 1 ~ (2048 - OffsetY) 2048 HTL?<CR><LF>...
User Manual (Ver. 1.0) - Short ASCII Command List GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Acquisition Control Related Topic: Trigger Control,Exposure Settings Name Access Short ASCII Values Default Description 0: Off TM=[Param.]<CR><LF> FrameStartTrig Mode TM?<CR><LF> 1: On TriggerSoftware (R)/W STRG 0, 1 STRG=0<CR><LF>...
User Manual (Ver. 1.0) - Short ASCII Command List GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Analog Control Related Topic: Gain Control, Black Level Control Name Access Short ASCII Values Default Description FGA=[Param.]<CR><L F> GainRawDigitalAll 100 ~1600 FGA?<CR><LF> 0: 0dB ABALL=[Param.]<CR><L F>...
User Manual (Ver. 1.0) - Short ASCII Command List GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Digital IO Control Related Topic: Digital IN/OUT Interface Name Access Short ASCII Values Default Description 0: False ND0INV1=[Param.]<CR><LF> LineInverter_Nand0In1 ND0INV1 1: True ND0INV1?<CR><LF> 0: False ND0INV2=[Param.]<CR><LF>...
User Manual (Ver. 1.0) - Short ASCII Command List GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 User Set Control Related Topic: Step 6: Save the Settings Short Name Access Values Default Description ASCII 0: Default 1: UserSet1 LD=[Param.]<CR><LF> UserSetLoad (R)/W LD?<CR><LF> 2: UserSet2...
Page 105
User Manual (Ver. 1.0) - Short ASCII Command List GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Short Name Access Values Default Description ASCII ShadingCorrection Mode SDCM=[Param.]<CR><LF> SDCM 0: Flat Shading Related Topic: SDCM?<CR><LF> Shading Correction ShadingCorrect RS=0<CR><LF> 0=Complete. 1=Too Bright. 2=Too dark...
Page 106
User Manual (Ver. 1.0) - Short ASCII Command List GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Short Name Access Values Default Description ASCII SequenceROI SQOY(n)=[Param.]<CR><LF> OffsetY(n) SQOY(n) 0 ~ 2047 SQOY(n)?<CR><LF> (n) = 1 ~ 128 SequenceROI Gain SQGA(n)=[Param.]<CR><LF> SQGA(n) 100 ~1600 SQGA(n)?<CR><LF>...
Page 107
User Manual (Ver. 1.0) - Short ASCII Command List GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Short Name Access Values Default Description ASCII MRH2=[Param.]<CR><LF> MultiRoiHeight2 MRH2 0 ~ 2048 MRH2?<CR><LF> MRH3=[Param.]<CR><LF> MultiRoiHeight3 MRH3 0 ~ 2048 MRH3?<CR><LF> MRH4=[Param.]<CR><LF> MultiRoiHeight4 MRH4 0 ~ 2048 MRH4?<CR><LF>...
Page 108
User Manual (Ver. 1.0) - Short ASCII Command List GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Short Name Access Values Default Description ASCII ExposureAutoMax ASCEA=[Param.]<CR><LF> ASCEA?<CR><LF> Related Topic: ASCEA 101 ~ 8000000[us] 18000 Exposure Maximum value is varied depending on frame rate.
Page 109
User Manual (Ver. 1.0) - Short ASCII Command List GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Short Name Access Values Default Description ASCII ALCLR ALC***=[Param.]<CR><LF> ALCLMR ALC***?<CR><LF> ALCLML 16 Photometry Areas and Short ASCII Commands ALCLL ALCMLR ALCHML ALCHMR ALCHL ALCHR ALCMLMR (Hight Mid-...
Page 110
User Manual (Ver. 1.0) - Short ASCII Command List GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Short Name Access Values Default Description ASCII 0: Free Run 1: Level High GpioPulseGen PGCM=[Param.]<CR><LF> PGCM 2: Level Low ClearMode0 PGCM?<CR><LF> 3: Rising Edge 4: Falling Edge...
Page 111
User Manual (Ver. 1.0) - Short ASCII Command List GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Short Name Access Values Default Description ASCII GpioNand1Input IND1INV1=[Param.]<CR><LF> IND1INV 1 Same as above. Invert1 IND1INV1?<CR><LF> 0:Non-Inv GpioNand0Input IND0INV2=[Param.]<CR><LF> IND0INV 2 Invert2 IND0INV2?<CR><LF> 1:Inv GpioNand1Input IND1INV2=[Param.]<CR><LF>...
User Manual (Ver. 1.0) - User's Record GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 User's Record Model name: …………… Revision: …………… Serial No: …………… Firmware version: …………… For camera revision history, please contact your local JAI distributor. - 119 -...
User Manual (Ver. 1.0) - Appendix GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Appendix Precautions Personnel not trained in dealing with similar electronic devices should not service this camera. The camera contains components sensitive to electrostatic discharge. The handling of these devices should follow the requirements of electrostatic sensitive components.
User Manual (Ver. 1.0) - Revision History GO-5000M-PMCL-1 | GO-5000M-PMCL-EP-1 | GO-5000M-PMCL-UV-1 Revision History Revision Date Device Version Changes 2023/06/19 DV0100 First Release Trademarks Other systems and product names described in this document are trademarks or registered trademarks of their respective owners. The ™ and ®...