Siemens SIPROTEC 7UM62 Manual page 577

Addr. Parameter
281 BkrClosed I MIN
295 TRANSDUCER 1
296 TRANSDUCER 2
297 TRANSDUCER 3
302 CHANGE
401 WAVEFORMTRIGGER
403 MAX. LENGTH
404 PRE. TRIG. TIME
405 POST REC. TIME
406 BinIn CAPT.TIME
610 FltDisp.LED/LCD
611 Spont. FltDisp.
615 T MIN LED HOLD
640 Start image DD
1108 ACTIVE POWER
1201 O/C I>
1202 I>
1203 T I>
1204 U< SEAL-IN
1205 U<
1206 T-SEAL-IN
1207A I> DOUT RATIO
1301 O/C I>>
1302 I>>
1303 T I>>
1304 Phase Direction
1305 LINE ANGLE
1401 O/C Ip
1402 Ip
1403 T Ip
1404 TIME DIAL: TD
SIPROTEC, 7UM62, Manual
C53000-G1176-C149-7, Release date 03.2010
Function C
P.System Data 1 5A 0.20 .. 5.00 A
1A 0.04 .. 1.00 A
P.System Data 1 10 V
4-20 mA
20 mA
P.System Data 1 10 V
4-20 mA
20 mA
P.System Data 1 with filter
without filter
Change Group Group A
Group B
Binary Input
Protocol
Osc. Fault Rec. Save w. Pickup
Save w. TRIP
Start w. TRIP
Osc. Fault Rec. 0.30 .. 5.00 sec
Osc. Fault Rec. 0.05 .. 4.00 sec
Osc. Fault Rec. 0.05 .. 0.50 sec
Osc. Fault Rec. 0.10 .. 5.00 sec; ∞
Device Target on PU
Target on TRIP
Device YES
NO
Device 0 .. 60 min
Device image 1
image 2
image 3
image 4
P.System Data 2 Generator
Motor
O/C Prot. I> OFF
ON
Block relay
O/C Prot. I> 5A 0.25 .. 100.00 A
1A 0.05 .. 20.00 A
O/C Prot. I> 0.00 .. 60.00 sec; ∞
O/C Prot. I> ON
OFF
O/C Prot. I> 10.0 .. 125.0 V
O/C Prot. I> 0.10 .. 60.00 sec
O/C Prot. I> 0.90 .. 0.99
O/C Prot. I>> OFF
ON
Block relay
O/C Prot. I>> 5A 0.25 .. 100.00 A
1A 0.05 .. 20.00 A
O/C Prot. I>> 0.00 .. 60.00 sec; ∞
O/C Prot. I>> Forward
Reverse
O/C Prot. I>> -90 .. 90 °
O/C Prot. Ip OFF
ON
Block relay
O/C Prot. Ip 5A 0.50 .. 20.00 A
1A 0.10 .. 4.00 A
O/C Prot. Ip 0.05 .. 3.20 sec; ∞
O/C Prot. Ip 0.50 .. 15.00 ; ∞
Setting Options Default Setting
0.20 A
0.04 A
10 V
10 V
with filter
Group A
Save w. Pickup
1.00 sec
0.20 sec
0.10 sec
0.50 sec
Target on PU
NO
5 min
image 1
Generator
OFF
6.75 A
1.35 A
3.00 sec
OFF
80.0 V
4.00 sec
0.95
OFF
21.50 A
4.30 A
0.10 sec
Reverse
60 °
OFF
5.00 A
1.00 A
0.50 sec
5.00
Appendix
A.7 Settings
Comments
Closed Breaker Min. Current
Threshold
Transducer 1
Transducer 2
Transducer 3
Change to Another Setting
Group
Waveform Capture
Max. length of a Waveform
Capture Record
Captured Waveform Prior to
Trigger
Captured Waveform after Event
Capture Time via Binary Input
Fault Display on LED / LCD
Spontaneous display of flt.an-
nunciations
Minimum hold time of lachted
LEDs
Start image Default Display
Measurement of Active Power for
Overcurrent Time Protection I>
I> Pickup
T I> Time Delay
State of Undervoltage Seal-in
Undervoltage Seal-in Pickup
Duration of Undervoltage Seal-in
I> Drop Out Ratio
Overcurrent Time Protection I>>
I>> Pickup
T I>> Time Delay
Phase Direction
Line Angle
Inverse O/C Time Protection Ip
Ip Pickup
T Ip Time Dial
TIME DIAL: TD
577