Table of Contents
Advertisement
I P 6 5 R AT E D
The International Protection (IP) rating system is commonly expressed as "IP" (Ingress Protection) followed
by two numbers (i.e. IP65), where the numbers define the degree of protection. The first digit (Foreign Bodies
Protection) indicates the extent of protection against particles entering the fixture, and the second digit (Water
Protection) indicates the extent of protection against water entering the fixture. An IP65 rated lighting fixture is
designed and tested to protect against the ingress of dust (6), and low-pressure water jets from any direction (5).
NOTE: THIS FIXTURE IS INTENDED FOR TEMPORARY OUTDOOR USE ONLY!
Maritime/Coastal Environment Installations: A coastal environment is seaside adjacent, and caustic to
electronics through exposure to atomized salt-water and humidity, whereas maritime is anywhere within 5-miles
of a coastal environment.
NOT suitable for maritime/coastal environment installations. Installing this fixture in a
maritime/coastal environment may cause corrosion and/or excessive wear to the interior
and/or exterior components of the fixture. Damages and/or performance issues resulting
from installation in a maritime/coastal environment will void the manufactures warranty, and
will NOT be subject to any warranty claims and/or repairs.
Maritime installations require additional preparation, and additional service intervals may be needed given the
maritime use. In general, IP ratings presuppose freshwater conditions VS maritime conditions, which are typically
more "caustic" to IP fixtures (both internally and externally). A duty-cycle may also be needed when units are not
in use. During times of high humidity and colder temperatures, condensation may occur internally so the fixture
may require a duty-cycle to bring it up to running temperature, allowing any accumulation of moisture to be
expelled via the vent valve. Recommendations can change based on installation environmental circumstances.
A waterproof dome or similar device is recommended for use in permanent outdoor installations. When using a
dome, refer to manufacturer recommendations for duty-cycle.
NOTE: NOT ALL FEATURES LISTED ARE AVAILABLE ON ALL FIXTURES; THE FOLLOWING
INSTRUCTIONS MAY NOT APPLY. CONTACT SUPPORT FOR ADDITIONAL DETAILS.
Exterior Maintenance: Inspect the exterior every 30-days. The unit must be powered off/disconnected. Inspect
optics to determine if the lens is obstructed, then clean optics and chassis accordingly. Based on initial finding,
schedule maintenance accordingly, keeping in mind that exterior maintenance will be required. Even if the
luminaires are NOT in use, maintenance will still be needed given its location (exterior use). The use of a durable
type of wax on the chassis is recommended since it will help prevent contaminant build up. Inspect both power
and data lines for any signs of contaminants or corrosion. Periodically reapplying di-electric grease, especially
in coastal environments. If any signs of corrosion/contaminants are present, clean thoroughly, and/or replace
connectors, then reapply di-electric grease. Typically, this should be done annually, or any time an opportunity
presents itself. As a preventive measure, annual replacement of both vent valves is recommended. The vent
valve membrane can become contaminated and/or clogged causing improper venting of humidity within the
luminaire. Inspect all mounting hardware as a precaution.
Interior Maintenance: Inspect the interior every 30-days. The unit must be powered off/disconnected.
•
Inspect zoom/focus mechanism, clean optics, lubricate linear bearings (Krytox oil) as needed, inspect belts
for wear
•
Inspect all rotating effect wheels, manually rotate them, note any resistance
•
Inspect all remaining rotating belts for any wear
•
Inspect all fans, clean as needed, check rotation, check connections
•
Inspect CMY module, manually move flags and check for signs of resistance, and if needed, clean guide rods
first, then reapply a thin layer of grease (moly lube)
•
Clean interior with low-volume compressed air, then clean optics prior to reassembly of head covers
Although the base has limited moving parts, the pan belt should also be inspected for wear. Remember to always
perform an IP test anytime a cover is removed.
There is no specific time frame regarding the routine replacement of parts such as belts/stepper motors, PCBs,
or LEDs. These items should only be replaced on an as needed bases, except for cooling fans, which should
be replaced once the luminaries reach 10,000-hours. This is a prophylactic measure intended to keep the unit
running as cool as possible, insuring proper function of all internal components. A complete service breakdown
is available, please contact
service@adj.com
for any needed parts or manuals.
7
Advertisement
Table of Contents
