Dc Output Connections - Redback A 4565B Operating Manual

Redback® A 4565B Evacuation Controller
2.5 24V OUTPUT CONNECTIONS
The A 4565B is fitted with five sets of 24V switched outputs for driving external devices such as strobes, sirens and attenu-
ators. Each output has a maximum current draw of 120mA. When connecting devices which require more than 24V DC @
120mA then an external supply and relays will be required.
In the illustration of figure 2.5 a high current school bell is to be activated by the Bell 24V switched output. As the current
draw of the Bell is more than 120mA, a relay board is used to switch an external power supply. The Altronics S 4444 24V
Relay Board as shown is an inexpensive and easily installed option designed for this purpose. 24V DC strobes such as the
Altronics S 5423, S 5430 and S 5435 strobes also draw more than 120mA so they are connected in the same fashion as
shown in figure 2.5.
Common 24V Out:
These contacts are for connection of override relays in remote volume controls. An override relay is necessary where
attenuators are used so that the alert tone, evac tone or message is broadcast at full volume regardless of the volume
setting on the individual volume control (attenuator).
The override relay can be set to "NORMAL" mode when connection is made between the N/O (normally open) contact
and the GND connection. In this configuration 24V appears when any of the alert tone, evac tone, voice over message or
paging functions are activated.
The override relay can be set to "FAILSAFE" mode when connection is made between the N/C (normally closed) contact
and the GND connection. In this configuration 24V is removed when any of the alert tone, evac tone, voice over message
or paging functions are activated.
Alert/Evac 24V Out:
These contacts are for switched 24V outputs whenever the alert or evac tones are activated. These may be used to run
external systems such as strobes in unusually noisy environments. These operate in the same manner as the common 24V
out contacts i.e. connection between the N/O contact and the GND contact will operate in NORMAL mode and connec-
tion between the N/C contact and the GND will operate in FAILSAFE mode.
Bell 24V Out:
These contacts are for operating an external relay used to operate something like a lunch bell etc.
These operate in the same manner as the switched 24V out contacts i.e.: connection between the N/O contact and the
GND contact will operate in NORMAL mode and connection between the N/C contact and GND will operate in FAILSAFE
mode.
IMPORTANT NOTE
Ensure power is switched off when
24V DC 24V DC adjusting DIP switches. New
settings will be effective when
IN IN
power is switched back on.
DIP Switches
Micro SD Card
1 2 3 4 5 6 7 8
- +
(16GB Maximum)
1 2 3 4 5 6 7 8
+24V
GND
N/C1
COM1
N/O1
N/C2
COM2
N/O2
24V Relay Board
(Altronics S 4444)
12 Redback® Proudly Made In Australia
Fire Evac Alert Bell Common
24V Out 24V Out 24V Out 24V Out 24V Out
Contacts
All switched outputs limited to 120mA maximum current draw
External External
+24V
24V DC Supply 24V DC Supply
GND
24V Strobes for
visual warning
(such as Altronics
S 5430 and S 5435)
1 2
PA Mic Evac Bell
3 To Wall Plates 4 To Paging
Vol Vol Vol
(Maximum 500mA per output) Console
+24V
GND
N/C1
+24V
COM1
GND
N/O1
N/C2
COM2
24V Bell
(eg school bell, lunch bell etc)
Fig 2.5
Attenuator tted
with over ride relay.
(such as Altronics A 2260)
L L L
R R R
Fire BGM Audio
V/Over Chime Audio BGM
Vol Vol Vol Out Volume In In
N/O2
24V Relay Board
(Altronics S 4444)
www.redbackaudio.com.au
Made in Australia by
Altronic Distributors
Pty Ltd
www.redbackaudio.com.au