I/O Signals; I/O. Cn Connector Signals; Ext. Cn Connector Signals - Yamaha SRCP30 User Manual

3-1 I/O Signals

3
2
3-
3-1 I/O Signals
The SRCP30 controller has two I/O interface connectors (EXT. CN and I/O. CN) as a standard
feature. The EXT. CN is used for emergency stop input and 24V power input for I/O control. The I/
O. CN is used for interlock signal input, dedicated command input, dedicated output, general-pur-
pose input and output, and feedback pulse output.

3-1-1 I/O. CN connector signals

The I/O. CN connector of the SRCP30 controller has 40 pins, with an individual signal assigned to
each pin. The following table shows the pin number as well as the name and description of each
signal assigned to each pin. For a more detailed description of each signal, refer to "3-2 Input Signal
Description" and onwards.
No. Pin No. Signal name
1 A1 ABS-PT Absolute point movement
command
3 A2
AUTO-R Automatic operation start command
5 A3 ORG-S
Return-to-origin command
7 A4 SERVO
Servo recovery command
9 A5 DI0 General-purpose input 0
11 A6 DI2 General-purpose input 2
13 A7 DI4 General-purpose input 4
15 A8 DI6 General-purpose input 6
17 A9 DO0 General-purpose output 0
19 A10 DO2 General-purpose output 2
21 A11 DO4 General-purpose output 4
23 A12 BUSY Command-in-progress output
25 A13 FG Frame ground
27 A14 GND Signal ground
29 A15 NC Reserved (Do not use.)
31 A16 NC Reserved (Do not use.)
33 A17
PA+ Feedback pulse output
35 A18 PB+ Feedback pulse output
37 A19 PZ+ Feedback pulse output
39 A20 PZM+ Feedback pulse output
n
NOTE
Pin B8 functions as the SERVICE mode input terminal only when the SERVICE mode function is enabled.

3-1-2 EXT. CN connector signals

The EXT. CN connector of the SRCP30 controller has 4 pins, with an individual signal assigned to
each pin. The following table shows the pin number as well as the name and description of each
signal assigned to each pin. For a more detailed description of each signal, refer to "3-2 Input Signal
Description" and onwards.
Pin No. Signal name Description
1 EMG1 Emergency stop input 1 (used with
EMG2)
3 24V 24V power supply for sequence input
n
NOTE
The positive polarity of the 24V DC must be connected to pin 3 (24V) and the negative polarity to pin 4 (24G).
Description No. Pin No. Signal name
2 B1
4 B2
6 B3
8 B4
10 B5
12 B6
14 B7
16 B8
18 B9
20 B10
22 B11
24 B12
26 B13
28 B14
30 B15
B16
32
34 B17
36 B18
38 B19
40 B20
Pin No. Signal name
2 EMG2
4 24G
Description
INC-PT Relative point movement command
STEP-R Step operation start command
RESET Reset command
LOCK
Interlock
DI1 General-purpose input 1
DI3 General-purpose input 3
DI5 General-purpose input 5
DI7/SVCE General-purpose input 7/SERVICE mode input
DO1 General-purpose output 1
DO3 General-purpose output 3
END End-of-run output
READY Ready-to-operate output
FG Frame ground
GND Signal ground
NC Reserved (Do not use.)
NC Reserved (Do not use.)
PA- Feedback pulse output
PB- Feedback pulse output
PZ- Feedback pulse output
PZM- Feedback pulse output
Description
Emergency stop input 2 (used with
EMG1)
24V power supply for sequence input