Effects That Connect Three Or More Types Of Effect In Series - Roland SC-8820 Owner's Manual

Effects
46: Cho Flanger (Chorus
This effect connects a chorus and a flanger in series.
fig.9-49
L
Chorus
R
Cho Dly (Chorus Pre Delay)
Adjusts the time delay from when the direct sound begins
until the chorus sound is heard.
Cho Rate (Chorus Rate)
Adjusts the modulation speed of the chorus effect.
Cho Depth (Chorus Depth)
Adjusts the modulation depth of the chorus effect.
+Cho Bal (Chorus Balance)
Adjusts the volume balance between the direct sound and
the chorus sound. With a setting of D>0E, only the direct
sound will be output. With a setting of D0<E, only the
chorus sound will be output.
"D" and "E" stand for "direct sound" and "effect sound"
respectively.
FL Dly (Flanger Pre Delay Time)
Adjusts the time delay from when the direct sound begins
until the flanger sound is heard.
FL Rate (Flanger Rate)
Adjusts the modulation speed of the flanger effect.
FL Depth (Flanger Depth)
Adjusts the modulation depth of the flanger effect.
FL Fb (Flanger Feedback Level)
Adjusts the proportion (%) of the flanger sound that is fed
back into the effect. Negative (-) settings will invert the
phase.
#FL Bal (Flanger Balance)
Adjusts the volume balance between the sound that passes
through the flanger and the sound that does not. With a
setting of D>0E, only the chorus sound will be output, and
with a setting of D0<E, the chorus sound that passes
through the flanger will be output.
"D" and "E" stand for "direct sound" and "effect sound"
respectively.
Low Gain
Adjusts the low frequency gain.
Hi Gain (High Gain)
Adjusts the high frequency gain.
Level (Output Level)
Adjusts the output level.
70
Flanger) [02H, 0BH]
EQ
Flanger
EQ
0–100ms [1 (40 03 03)]
0.05–10.0 [2 (40 03 04)]
0–127 [3 (40 03 05)]
100:0–0:100(D:E) [5 (40 03 07)]
0–100ms [6 (40 03 08)]
0.05–10.0 [7 (40 03 09)]
0–127 [8 (40 03 0A)]
-98%–+98% [9 (40 03 0B)]
100:0–0:100(D:E) [10 (40 03 0C)]
-12–+12 [17 (40 03 13)]
-12–+12 [18 (40 03 14)]
0–127 [20 (40 03 16)]
Effects that connect three or more types of
effect in series (series 3/series 4/series 5)
47: Rotary Multi
This connects Overdrive (OD), 3-band equalizer (EQ), and
Rotary (RT) effects in series.
fig.9-50
L
Over
drive
R
OD (Overdrive)
+OD Drive
Adjusts the degree of distortion. The volume will change
together with the degree of distortion.
OD Sw (Overdrive Switch)
Turns the Overdrive effect on/off.
EQ (Equalizer)
EQ L Gain (EQ Low Gain)
Adjusts the low range gain of the equalizer.
EQ M Fq (EQ Mid Frequency)
Sets the center frequency for the equalizer mid-range.
EQ M Q (EQ Mid Q)
Adjusts the width of the area centered at the EQ M Fq
setting in which the gain will be affected. The area affected
will become narrower as this value is increased.
EQ M Gain (EQ Mid Gain)
Adjusts the gain of the area specified by the EQ M Fq
parameter and the EQ M Q parameter.
EQ H Gain (EQ High Gain)
Adjusts the high-range gain of the equalizer.
RT (Rotary)
RT L Slow (RT Low Frequency Slow Rate)
Adjusts the speed of the low-range rotor for the slow-speed
setting.
RT L Fast (RT Low Frequency Fast Rate)
Adjusts the speed of the low-range rotor for the fast-speed
setting.
RT Lo Accl (RT Low Frequency Acceleration)
Adjusts the time over which the rotation speed of the low-
range rotor will change from slow-speed to fast-speed (or
fast-speed to slow-speed) rotation. Smaller values will
require greater time to reach the new rotational speed.
RT Lo Lev (RT Low Frequency Level)
Adjusts the volume of the low-range rotor.
[03H, 00H]
Rotary
EQ
0–127 [1 (40 03 03)]
Off/On [2 (40 03 04)]
-12–+12 [3 (40 03 05)]
200–6.3k [4 (40 03 06)]
0.5/1.0/2.0/4.0/9.0 [5 (40 03 07)]
-12–+12 [6 (40 03 08)]
-12–+12 [7 (40 03 09)]
0.05–10.0 [8 (40 03 0A)]
0.05–10.0 [9 (40 03 0B)]
0–15 [10 (40 03 0C)]
0–127 [11 (40 03 0D)]