Od/Phaser (Overdrive/Distortion, Phaser) - Roland SC-8820 Owner's Manual

RT H Slow (RT High Frequency Slow Rate)
Adjusts the speed of the high-range rotor for the slow-
speed setting.
RT H Fast (RT High Frequency Fast Rate)
Adjusts the speed of the high-range rotor for the fast-speed
setting.
RT Hi Accl (RT High Frequency Acceleration)
Adjusts the time over which the rotation speed of the high-
range rotor will change from slow-speed to fast-speed (or
fast-speed to slow-speed) rotation. Smaller values will
require greater time to reach the new rotational speed.
RT Hi Lev (RT High Frequency Level)
Adjusts the volume of the high-range rotor.
RT Sept (RT Separation)
Adjusts the spatial spread of the rotary sound.
#RT Speed
Simultaneously switch the rotational speed of both the low-
range and the high-range rotors.
Slow: Slow down the rotation to the specified
speeds (RT L Slow parameter/RT H Slow
parameter values).
Fast: Speed up the rotation to the specified speeds
(RT L Fast parameter/RT H Fast parameter
values).
RT Pan (RT Output Pan)
Adjusts the stereo position of the rotary sound. L63 is far
left, 0 is center, and R63 is far right.
RT Level
Adjusts the volume of the rotary sound.
Level (Output Level)
Adjusts the output level.
0.05–10.0 [10 (40 03 0C)]
0.05–10.0 [11 (40 03 0D)]
0–15 [12 (40 03 0E)]
0–127 [13 (40 03 0F)]
0–127 [14 (40 03 10)]
Slow/Fast [15 (40 03 11)]
L63–0–R63 [18 (40 03 14)]
0–127 [19 (40 03 15)]
0–127 [20 (40 03 16)]
61: OD/Phaser (Overdrive/Distortion, Phaser) [11H, 05H]
This connects an overdrive or distortion in parallel with a
phaser.
fig.9-66
Overdrive/
L
Distortion
R
Phaser
OD (Overdrive/Distortion)
OD Sel (OD Select)
Selects either Overdrive or Distortion.
+OD Drive (OD Drive)
Adjusts the degree of distortion. The volume will change
together with the degree of distortion.
OD Amp (Overdrive Amp Simulator Type)
Smal/BltIn/2-Stk/3-Stk [3 (40 03 05)]
Selects the type of guitar amp.
Small: small amp
BltIn: single-unit type amp
2-Stk: large double stack amp
3-Stk: large triple stack amp
OD Amp Sw (OD Amp Switch)
Turns the OD Amp parameter on/off.
OD Pan (OD Output Pan)
Sets the stereo location of the overdrive or distortion sound.
L63 is far left, 0 is center, and R63 is far right.
OD Level
Adjusts the overdrive or distortion volume.
PH (Phaser)
PH Man (Phaser Manual)
Adjusts the center frequency at which the sound will be
modulated.
#PH Rate (Phaser Rate)
Adjusts the modulation speed.
PH Depth (Phaser Depth)
Adjusts the modulation depth.
PH Reso (Phaser Resonance)
Adjusts the emphasis for the region around the center
frequency specified by the PH Man parameter.
PH Mix (Phaser Mix Level)
Adjusts the proportion of the phase-shifted sound that will
be mixed with the direct sound.
PH Pan (Phaser Output Pan) L63–0–R63 [18 (40 03 14)]
Sets the stereo location of the phaser sound. L63 is far left, 0
is center, and R63 is far right.
PH Level
Adjusts the volume of the phaser sound.
Level (Output Level)
Adjusts the output level.
Effects
Pan
Pan
Odrv/Dist [1 (40 03 03)]
0–127 [2 (40 03 04)]
Off/On [4 (40 03 06)]
L63–0–R63 [16 (40 03 12)]
0–127 [17 (40 03 13)]
100–8.0k [6 (40 03 08)]
0.05–10.0 [7 (40 03 09)]
0–127 [8 (40 03 0A)]
0–127 [9 (40 03 0B)]
0–127 [10 (40 03 0C)]
0–127 [19 (40 03 15)]
0–127 [20 (40 03 16)]
81