Roland SC-8820 Owner's Manual page 66

Effects
38: DS Chorus (Distortion
This effect connects a distortion and a chorus in series.
fig.9-41
L
Distortion
R
DS Drive (Distortion Drive)
Adjusts the degree of distortion. The volume will change
together with the degree of distortion.
+DS Pan (Distortion Output Pan) L63–0–R63 [2 (40 03 04)]
Adjusts the stereo location of the distortion sound. L63 is
far left, 0 is center, and R63 is far right.
DS Amp (Distortion Amp Simulator Type)
Small/BltIn/2-Stk/3-Stk [3 (40 03 05)]
Selects the type of guitar amp.
Small: small amp
BltIn: single-unit type amp
2-Stk: large double stack amp
3-Stk: large triple stack amp
DS Amp Sw (Distortion Amp Switch) Off/On [4 (40 03 06)]
Turns DS Amp on/off.
Cho Dly (Chorus Pre Delay)
Adjusts the time delay from when the direct sound begins
until the chorus sound is heard.
Cho Rate (Chorus Rate)
Adjusts the modulation speed of the chorus effect.
Cho Depth (Chorus Depth)
Adjusts the modulation depth of the chorus effect.
#Cho Bal (Chorus Balance)
Adjusts the volume balance between the sound that passes
through the chorus and the sound that does not. With a
setting of D>0E, only the distortion sound will be output,
and with a setting of D0<E, the distortion sound that passes
through the chorus will be output.
"D" and "E" stand for "direct sound" and "effect sound"
respectively.
Low Gain
Adjusts the low frequency gain.
Hi Gain (High Gain)
Adjusts the high frequency gain.
Level (Output Level)
Adjusts the output level.
66
Chorus) [02H, 03H]
EQ
Chorus Balance
EQ
0–127 [1 (40 03 03)]
0–100ms [6 (40 03 08)]
0.05–10.0 [7 (40 03 09)]
0–127 [8 (40 03 0A)]
100:0–0:100(D:E) [10 (40 03 0C)]
-12–+12 [17 (40 03 13)]
-12–+12 [18 (40 03 14)]
0–127 [20 (40 03 16)]
39: DS Flanger (Distortion
This effect connects a distortion and a flanger in series.
fig.9-42
L
Distortion
R
DS Drive (Distortion Drive)
Adjusts the degree of distortion. The volume will change
together with the degree of distortion.
+DS Pan (Distortion Output Pan) L63–0–R63 [2 (40 03 04)]
Adjusts the stereo location of the distortion sound. L63 is
far left, 0 is center, and R63 is far right.
DS Amp (Distortion Amp Simulator Type)
Small/BltIn/2-Stk/3-Stk [3 (40 03 05)]
Selects the type of guitar amp.
Small: small amp
BltIn: single-unit type amp
2-Stk: large double stack amp
3-Stk: large triple stack amp
DS Amp Sw (Distortion Amp Switch) Off/On [4 (40 03 06)]
Turns DS Amp on/off.
FL Dly (Flanger Pre Delay)
Adjusts the time delay from when the direct sound begins
until the flanger sound is heard.
FL Rate (Flanger Rate)
Adjusts the modulation speed of the flanger effect.
FL Depth (Flanger Depth)
Adjusts the modulation depth of the flanger effect.
FL Fb (Flanger Feedback Level)
Adjusts the proportion (%) of the flanger sound that is fed
back into the effect. Negative (-) settings will invert the
phase
#FL Bal (Flanger Balance)
Adjusts the volume balance between the sound that passes
through the flanger and the sound that does not. With a
setting of D>0E, only the distortion sound will be output,
and with a setting of D0<E, the distortion sound that passes
through the flanger will be output.
"D" and "E" stand for "direct sound" and "effect sound"
respectively.
Low Gain
Adjusts the low frequency gain.
Hi Gain (High Gain)
Adjusts the high frequency gain.
Level (Output Level)
Adjusts the output level.
Flanger) [02H, 04H]
EQ
Flanger Balance
EQ
0–127 [1 (40 03 03)]
0–100ms [6 (40 03 08)]
0.05–10.0 [7 (40 03 09)]
0–127 [8 (40 03 0A)]
-98%–+98% [9 (40 03 0B)]
100:0–0:100(D:E) [10 (40 03 0C)]
-12–+12 [17 (40 03 13)]
-12–+12 [18 (40 03 14)]
0–127 [20 (40 03 16)]