Effects That Connect Two Types Of Effect In Series - Roland SC-8820 Owner's Manual

Effects
Hum LPF (Hum Noise LPF)
250–6.3 k/Bypass [13 (40 03 0F)]
Specifies the cutoff frequency of the low pass filter that is
applied to the hum noise.
Hum Level (Hum Noise Level)
Specifies the volume of the hum noise.
M/S (Mono/Stereo Switch)
Selects whether the effect sound will be monaural or stereo.
#Balance (Effect Balance)100:0–0:100(D:E) [16 (40 03 12)]
Adjusts the volume balance between the direct and the
effect sound.
"D" and "E" stand for "direct sound" and "effect sound"
respectively.
Low Gain
Adjusts the gain of the low frequency range.
Hi Gain (High Gain)
Adjusts the gain of the high frequency range.
Pan (Mono) (Output Pan (Mono))
When Mono mode is used, adjust the stereo location of the
output sound. L63 is far left, 0 is center, and R63 is far right.
Level (Output Level)
Adjusts the output level.
64
0–127 [14 (40 03 10)]
Mono/Stereo [15 (40 03 11)]
-12–+12 [17 (40 03 13)]
-12–+12 [18 (40 03 14)]
L63–0–R63 [19 (40 03 15)]
0–127 [20 (40 03 16)]

Effects that connect two types of effect in series

(series 2)
35: OD Chorus (Overdrive
This effect connects an overdrive and a chorus in series.
fig.9-38
L
Overdrive
R
OD Drive (Overdrive Drive)
Adjusts the degree of overdrive distortion. The volume will
change together with the degree of distortion.
+OD Pan (Overdrive Drive Output Pan)
Adjusts the stereo location of the overdrive sound. L63 is
far left, 0 is center, and R63 is far right.
OD Amp (Overdrive Amp Simulator Type)
Small/BltIn/2-Stk/3-Stk [3 (40 03 05)]
Selects the type of guitar amp.
Small: small amp
BltIn: single-unit type amp
2-Stk: large double stack amp
3-Stk: large triple stack amp
OD Amp Sw (Overdrive Amp Switch)
Turns OD Amp on/off.
Cho Dly (Chorus Pre Delay)
Adjusts the time delay from when the direct sound begins
until the chorus sound is heard.
Cho Rate (Chorus Rate)
Adjusts the modulation speed of the chorus effect.
Cho Depth (Chorus Depth)
Adjusts the modulation depth of the chorus effect.
#Cho Bal (Chorus Balance)
Adjusts the volume balance between the sound that passes
through the chorus and the sound that does not. With a
setting of D>0E, only the overdrive sound will be output,
and with a setting of D0<E, the overdrive sound that passes
through the chorus will be output.
"D" and "E" stand for "direct sound" and "effect sound"
respectively.
Low Gain
Adjusts the low frequency gain.
Hi Gain (High Gain)
Adjusts the high frequency gain
Level (Output Level)
Adjusts the output level.
Chorus) [02H, 00H]
EQ
Chorus Balance
EQ
0–127 [1 (40 03 03)]
L63–0–R63 [2 (40 03 04)]
Off/On [4 (40 03 06)]
0–100ms [6 (40 03 08)]
0.05–10.0 [7 (40 03 09)]
0–127 [8 (40 03 0A)]
100:0–0:100(D:E) [10 (40 03 0C)]
-12–+12 [17 (40 03 13)]
-12–+12 [18 (40 03 14)]
0–127 [20 (40 03 16)]