Danfoss VLT FC 100 Instruction Manual page 97

Index
P
Parameter Settings..................................................................... 4-3, 5-4
PELV................................................................................... 2-21, 6-1, 10-6
Phase Loss.............................................................................................. 8-5
Power
Power.................................................................................................. 2-6
Connections..................................................................................... 2-6
Factor................................................................................. 1-4, 2-7, 3-1
Pre-Installation Check List................................................................ 2-1
Product Overview............................................................................... 1-1
Programming.................... 1-3, 3-4, 4-2, 5-4, 5-9, 8-5, 3-2, 4-1, 4-3
Protection
Protection....................................................................................... 10-8
And Features.................................................................................. 10-8
Pulse Inputs........................................................................................ 10-5
Q
Quick
Menu.................................................................................. 4-2, 5-1, 4-2
Set-up................................................................................................. 3-2
R
Ramp-down Time............................................................................... 3-4
Ramp-up Time...................................................................................... 3-4
Reference..................................................................... 0-iii, 6-1, 4-2, 5-1
Relay Outputs.......................................................................... 2-22, 10-6
Remote
Commands........................................................................................ 1-3
Programming................................................................................... 5-9
Reference........................................................................................... 7-1
Reset................................................. 4-1, 4-4, 7-1, 8-5, 8-11, 10-8, 4-3
Residual Current Devices (RCDs)................................................... 2-6
Restoring Default Settings............................................................... 4-4
RFI Filter............................................................................................... 2-20
RMS Current.......................................................................................... 1-4
RS-485................................................................................................... 2-24
Run
Command......................................................................................... 3-4
Permissive......................................................................................... 7-1
S
Serial Communication................................ 1-3, 2-22, 4-3, 7-1, 2-24
Setpoint.................................................................................................. 7-1
Set-up...................................................................................................... 4-2
Shielded
Cable........................................................................................... 2-3, 3-1
Control Cables............................................................................... 2-22
Wire..................................................................................................... 2-5
®
VLT HVAC Drive D-Frame
Instruction Manual
®
MG16D222 - VLT is a registered Danfoss trademark
Short Circuit.......................................................................................... 8-7
Smart Application Set-up (SAS)..................................................... 3-2
Specifications....................................................................................... 1-3
Speed Reference.............................................................. 2-23, 3-4, 5-1
Start Up................................................................................................... 9-1
Startup............................................................................................ 1-3, 5-1
Start-up................................................................................................... 4-4
Status
Messages........................................................................................... 7-1
Mode................................................................................................... 7-1
Stop Command.................................................................................... 7-1
Supply Voltage.................................................... 2-21, 2-22, 8-8, 10-5
Surroundings..................................................................................... 10-7
Switching Frequency......................................................................... 7-1
System Feedback................................................................................ 1-3
T
Temperature Limits............................................................................ 3-1
Terminal
53...................................................................................... 5-1, 2-23, 5-1
54....................................................................................................... 2-23
Locations D1h.................................................................................. 2-8
Locations D2h............................................................................... 2-10
Programming................................................................................ 2-23
Programming Examples............................................................... 5-3
Thermistor
Thermistor..................................................................... 2-21, 8-6, 6-1
Control Wiring............................................................................... 2-21
Torque
Characteristics............................................................................... 10-4
For Terminals............................................................................... 10-10
Limit..................................................................................................... 3-4
Transient Protection.......................................................................... 1-4
Trip Function........................................................................................ 2-5
Troubleshooting................................................................. 1-3, 8-5, 9-1
U
Uploading Data To The LCP............................................................ 4-4
Using Shielded Control Cables.................................................... 2-21
V
Voltage Imbalance.............................................................................. 8-5
W
Warning And Alarm Definitions..................................................... 8-3
Wire Type And Ratings...................................................................... 2-6
Wiring To Control Terminals......................................................... 2-23
12-3