Advertisement
Quick Links
Advertisement
Related Manuals for TASKING iSYSTEM Aurora MPC5 Series
Summary of Contents for TASKING iSYSTEM Aurora MPC5 Series
- Page 1 MPC5x/SPC5x Aurora Active Probe User Manual V2.1, June 2023 isystem.com/start...
- Page 2 General safety instructions Please read the following safety precautions carefully before putting this device to use to avoid any personal injuries, damage to the instrument, or to the target system. Use this instrument only for its intended purpose as specified by this manual to prevent potential hazards. Use included power cord and power supply The enclosed power supply has been approved for use by iSYSTEM.
-
Page 3: Table Of Contents
Contents Package content ..........................4 Specifications ............................5 Operation ............................... 6 mDIO Cable ..............................8 14-pin 2.54mm JTAG Converter ......................9 Hardware Setup and Configuration ..................10 Accessories ............................11... -
Page 4: Package Content
Package content MPC5x/SPC5x Aurora Active Probe enables debugging, tracing and testing of NXP MPC5xxx, NXP S32R and ST SPC5 microcontroller families. Besides the standard JTAG debug interface it supports also a high-speed Aurora trace interface operating at its maximum frequency. Its small and compact hardware size allows for connecting to a target microcontroller in a confined space as far as 10 m away. -
Page 5: Specifications
Specifications GENERAL Supply voltage 9.0V DC via FNet cable Operating temperature 10°C to 40°C Storage temperature -10°C to 60°C Humidity 5% to 80% RH MECHANICAL Size 80 x 55 x 18 mm Weight 0.125 kg OPERATION Communication interface iSYSTEM proprietary FNet to BlueBox Debug signal valid input 3.3V (max. -
Page 6: Operation
Operation A – 34-pin ERF8 MPC5xxx/SPC5 target pinout: Signal Signal Signal Description Signal Signal Signal Description Direction Direction AGBT TX0_P TX0+ Vref Reference Voltage AGBT TX0_N TX0- JTAG Ground JTAG AGBT TX1_P* TX1+ JTAG AGBT TX1_N* TX1- JTAG Ground nJCOMP JTAG TRST (optional) AGBT TX2_P* TX2+... - Page 7 Signal direction definition: O - Output from the Active Probe to the target microcontroller I - Input to the Active Probe from the target microcontroller B – mDIO port marked as TRIG on the housing mDIO port provides two digital signals, which can interact with the embedded target. Each can be configured either for input or output operation.
-
Page 8: Mdio Cable
mDIO Cable Ordering code BB-AP-MDIO-20 mDIO Cable is used to connect the Active Probe mDIO port with the signals around the debugged microcontroller, which can then be either read or controlled by the debugger. For example, the debugger can periodically service an external watchdog through the mDIO output or just read and record an external signal through the mDIO input. -
Page 9: 14-Pin 2.54Mm Jtag Converter
14-pin 2.54mm JTAG Converter Ordering code IASAM34MPCPIN14 If your target features 14-pin 2.54mm pitch JTAG target debug connector, use iSYSTEM 14-pin 2.54 mm JTAG Converter which acts as a pinout converter. It must be ordered separately. The converter is used only in conjunction with iSYSTEM solutions supporting MPC5xxx/SPC5 Aurora trace interface (e.g. -
Page 10: Hardware Setup And Configuration
Hardware Setup and Configuration For detailed visual presentation of the hardware setup and configuration, refer to Getting started tutorial. Use short link isystem.com/start. 1. Connect the power supply cable. BlueBox should be switched off. 2. First connect via USB. Later you can configure TCP/IP connection to work remotely. 3. -
Page 11: Accessories
Accessories Analog/Digital and Network Trace Ordering Code Description IC57031 IOM6 Hub (3 x FNet & FBridge) IC57040 IOM6 CAN/LIN IC57041 IOM6 ADIO IC57125-1 ARM HSSTP II Active Probe IC57163-1 Infineon DAP/DAPE II Active Probe IC57164 Infineon AGBT Active Probe IC57150 MPC5x/SPC5x Aurora Active Probe IC57166 Infineon SGBT (HSTCU) Active Probe... - Page 12 Visit our website for: Support - isystem.com/support · Tutorials - isystem.com/getting-started · Knowledge Base - kb.isystem.com · www.isystem.com...
Need help?
Do you have a question about the iSYSTEM Aurora MPC5 Series and is the answer not in the manual?
Questions and answers