CDVI A22k Quick Start Manual

PLAN YOUR A22K NETWORK CONNECTIVITY
1
500 door system (100 doors connected IP + 400 doors connected RS485)
the "Master" controller to manage the others. These forty (49) others are de ned as "Sub-Controllers".
"MASTER"
CONTROLLER
The "Master" controller
manages up to forty nine (49)
"Sub-Controllers".
(100 doors fully IP)
AES256
E N C R Y P T I O N
IP Network
Maximum 300 ft (100 m)
+12V DC
A+
B-
Input 1
Input 2
Output 1
+12V DC
Output 2
BUZ GRN RED D1 D0 GND 12V BUZ GRN RED D1 D0 GND 12V C1 GND REX1 12V C2 GND REX2 12V
A22K "Master" or "Sub-Controllers"
RS485 port (orange connector).
Maximum 4000 ft
(1220 m)
+12V DC
A+
B-
Input 1
Input 2
Output 1
+12V DC
Output 2
ENCLOSURE
TAMPER
INPUT INPUT SWITCH
READER DOOR 1 READER DOOR 2 DOOR 1 DOOR 2 INPUT
BUZ GRN RED D1 D0 GND 12V BUZ GRN RED D1 D0 GND 12V C1 GND REX1 12V C2 GND REX2 12V GND TMP LK1+ LK1-
A22K set as "Expander"
IP CONNECTIVITY
Out of the box the A22K is ready for IP connectivity, fty (50) A22K per account.
If you have more than one A22K controller per account, one must be set as
+12V DC
A+
B-
Input 1
Input 2
Output 1
+12V DC
Output 2
BUZ GRN RED D1 D0 GND 12V BUZ GRN RED D1 D0 GND
LAN or WAN
+12V DC
+24V DC
-
A+
B-
Input 1
Input 2
+12V DC Output 1
- +12V DC
Output 2
GND TMP LK1+ LK1- C1 NO1 NC1 LK2+ LK2- C2 NO2 NC2 BUZ GRN RED D1
"SUB-CONTROLLERS"
Up to forty nine (49) A22K de ned as "Sub-Controllers".
RS485 CONNECTIVITY
An A22K can be set as an "Expander". Up to four (4) can be connected to the
RS485 network (orange connector) of the "Master" and each "Sub-Controller".
+12V DC
Use twisted pair wiring
for RS485 connection
(1 pair for ground and 1
A+
pair for A+ B-)
B-
+12V DC
+24V DC
-
A+
B-
Input 1
Input 2
+12V DC
Output 1
-
+12V DC
Output 2
ENCLOSURE
TAMPER
LOCK LOCK
INPUT INPUT SWITCH
DOOR 1 DOOR 2
READER DOOR 1 READER DOOR 2 DOOR 1 DOOR 2 INPUT
C1 NO1 NC1 LK2+ LK2- C2 NO2 NC2
BUZ GRN RED D1 D0 GND 12V BUZ GRN RED D1 D0 GND 12V C1 GND REX1 12V C2 GND REX2 12V GND TMP
A22K set as "Expander"
a22k
quick start Guide
+24V DC
-
+12V DC
-
12V C1 GND REX1 12V C2 GND REX2 12V GND TMP LK1+ LK1- C1 NO1 NC1 LK2+ LK2- C2 NO2 NC2
+24V DC
-
+12V DC
-
D0 GND 12V BUZ GRN RED D1 D0 GND 12V C1 GND REX1 12V C2 GND REX2 12V GND TMP LK1+ LK1- C1 NO1 NC1 LK2+ LK2- C2 NO2 NC2
How to set an A22K as an "Expander"
On power OFF, move the "Module Type"
jumper setting to the two pins closest to "EX".
EX
+12V DC
+24V DC
-
A+
B-
Input 1
Input 2
+12V DC
Output 1
- +12V DC
Output 2
ENCLOSURE
TAMPER
LOCK LOCK INPUT INPUT SWITCH
DOOR 1 DOOR 2 READER DOOR 1 READER DOOR 2 DOOR 1 DOOR 2 INPUT
LK1+ LK1- C1 NO1 NC1 LK2+ LK2- C2 NO2 NC2 BUZ GRN RED D1 D0 GND 12V BUZ GRN RED D1 D0 GND 12V C1 GND REX1 12V C2 GND REX2 12V GND
A22K set as "Expander"
2-Door / 4-reaDer Controller
Communication between the
"Master" controller and
"Sub-Controllers" is
established via TCP/IP ONLY.
+12V DC
+24V DC
-
A+
B-
Input 1
Input 2
Output 1 +12V DC
+12V DC -
Output 2
BUZ GRN RED D1 D0 GND 12V BUZ GRN RED D1 D0 GND 12V C1 GND REX1 12V C2 GND REX2 12V GND TMP LK1+ LK1- C1 NO1 NC1 LK2+ LK2- C2 NO2 NC2
CT
DO NOT use IP connection
when an A22K is set as an
"Expander".
+24V DC +12V DC
-
A+
B-
Input 1
Input 2
+12V DC
Output 1
-
+12V DC
Output 2
ENCLOSURE
LOCK LOCK
INPUT INPUT
DOOR 1 DOOR 2
READER DOOR 1 READER DOOR 2 DOOR 1 DOOR 2
TMP LK1+ LK1- C1 NO1 NC1 LK2+ LK2- C2 NO2 NC2
BUZ GRN RED D1 D0 GND 12V BUZ GRN RED D1 D0 GND 12V C1 GND REX1 12V C2 GND REX2 12V
A22K set as "Expander"
+24V DC
-
+12V DC
-
TAMPER
SWITCH LOCK LOCK
INPUT DOOR 1 DOOR 2
GND TMP LK1+ LK1- C1 NO1 NC1 LK2+ LK2- C2 NO2 NC2