Tranquility ® Digital (TE) Series Table of Contents Model Nomenclature General Information Unit Physical Data Horizontal Installation Field Conversion of Air Discharge Horizontal Installation Vertical Installation Piping Installation vFlow™ Heat Pump Applications Overview Water-Loop Heat Pump Applications Ground-Loop Heat Pump Applications Ground-Loop and Ground Water Heat Pump Applications Ground-Water Heat Pump Applications...
Page 2
C L I M A T E M A S T E R W A T E R - S O U R C E H E A T P U M P S Tr a n q u i l i t y 3 0 D i g i t a l ( T E ) ®...
T H E S M A R T S O L U T I O N F O R E N E R G Y E F F I C I E N C Y Tr a n q u i l i t y 3 0 D i g i t a l ( T E ) ®...
Page 8
(e.g. louvered door). Therefore, fi lter rails are the industry coated air coils. standard and are included on ClimateMaster commercial heat pumps for the purposes of holding the fi lter only. For ducted return applications, the fi lter rail must be removed and replaced with a duct fl...
(e.g. louvered door). Therefore, fi lter rails are the industry transition duct to reduce noise standard and are included on ClimateMaster commercial heat pumps for the purposes of holding the fi lter only. For ducted return applications, the fi lter rail must be removed and replaced with a duct fl...
Page 12
C L I M A T E M A S T E R W A T E R - S O U R C E H E A T P U M P S Tr a n q u i l i t y 3 0 D i g i t a l ( T E ) ®...
Optional pressure-rated hose assemblies designed causing unnecessary noise complaints. specifi cally for use with ClimateMaster units are available. Similar hoses can be obtained from alternate suppliers. Figure 11: Supply/Return Hose Kit Supply and return hoses are fi tted with swivel-joint fi ttings at one end to prevent kinking during installation.
Hose kits are available from ClimateMaster in different treatment and fi ltering will be necessary. confi gurations for connection between the unit and the piping system.
20 mesh] size. The ClimateMaster Water Quality Table provides water quality requirements for ClimateMaster coaxial heat exchangers. The water should be evaluated by an Rev.: 5/6/2014 S independent testing facility comparing to this Table and when properties are outside of these requirements, an external secondary heat exchanger must be used to isolate the heat pump heat exchanger from the unsuitable water.
fi eld selection of low water (or water- temperature when using an antifreeze solution. All antifreeze solution) temperature limit by clipping jumper ClimateMaster units operating with entering water JW3, which changes the sensing temperature associated temperatures below 60°F [15.6°C] must include the with thermistor LT1.
Relay external solenoid valve. Figures 19 and 20 illustrate typical slow closing water control valve wiring for Taco 500 series (ClimateMaster P/N AVM) and Taco SBV series valves. Slow closing valves take approximately T2 T2 T3 T3 T4 T4 T5 T6 T6 60 seconds to open (very little water will fl...
IOM and or unit wiring diagram. Practically back plate against the wall so that it appears level and any heat pump thermostat will work with ClimateMaster so the thermostat wires protrude through the middle units, provided it has the correct number of heating and cooling stages.
The cooling/heating modes are like any other • Reheat Mode: A call from the Humidistat/Dehumidistat ClimateMaster WSHP. The reversing valve (“O” signal) to the (H) terminal of the DXM2 control board will is energized in cooling, along with the compressor bring the unit on in Reheat Mode if there is no call contactor(s) and blower relay.
Page 47
T H E S M A R T S O L U T I O N F O R E N E R G Y E F F I C I E N C Y Tr a n q u i l i t y 3 0 D i g i t a l ( T E ) ®...
Page 48
C L I M A T E M A S T E R W A T E R - S O U R C E H E A T P U M P S Tr a n q u i l i t y 3 0 D i g i t a l ( T E ) ®...
Sizes 064-072 properly. Closed Closed 4. Verify that all strainers are in place (ClimateMaster recommends a strainer with a #20 stainless steel wire mesh). Start the pumps, and systematically check each vent to ensure that all air is bled from the system.
Page 51
T H E S M A R T S O L U T I O N F O R E N E R G Y E F F I C I E N C Y Tr a n q u i l i t y 3 0 D i g i t a l ( T E ) ®...
If temperature is within 5. Two factors determine the operating limits range, proceed with the test. If temperature is of ClimateMaster heat pumps, (a) return air outside of the operating range, check refrigerant temperature, and (b) water temperature. When any pressures and compare to table 11.
97B0075N17 ClimateMaster works continually to improve its products. As a result, the design and specifi cations of each product at the time for order may be changed without notice and may not be as described herein. Please contact ClimateMaster’s Customer Service Department at 1-405-745-6000 for specifi c information on the current design and specifi...