Tranquility ® High Efficiency (TR) Series ( ( T T R R ) ) S S e e r r i i e e s s Table of Contents Model Nomenclature - General Overview General Information Unit Physical Data Horizontal Installation Field Conversion of Air Discharge Horizontal Installation Vertical Installation...
Page 2
C L I M A T E M A S T E R W A T E R - S O U R C E H E A T P U M P S Tr a n q u i l i t y ( T R ) S e r i e s ®...
T H E S M A R T S O L U T I O N F O R E N E R G Y E F F I C I E N C Y Tr a n q u i l i t y ( T R ) S e r i e s ®...
Page 8
(e.g. louvered door). Therefore, fi lter rails are the industry e-coated air coils. standard and are included on ClimateMaster commercial heat pumps for the purposes of holding the fi lter only. For ducted return applications, the fi lter rail must be removed and replaced with a duct fl...
C L I M A T E M A S T E R W A T E R - S O U R C E H E A T P U M P S Tr a n q u i l i t y Tr a n q u i l i t y Tr a n q u i l i t y ( T R ) S e r i e s...
(e.g. louvered door). Therefore, fi lter rails are the industry standard and are included on ClimateMaster commercial heat pumps for the purposes of holding the fi lter only. For ducted return applications, the fi lter rail must be removed and replaced with a duct fl...
Page 12
C L I M A T E M A S T E R W A T E R - S O U R C E H E A T P U M P S Tr a n q u i l i t y ( T R ) S e r i e s ®...
Optional pressure-rated hose assemblies designed causing unnecessary noise complaints. specifi cally for use with ClimateMaster units are available. Similar hoses can be obtained from alternate suppliers. Supply and return hoses are fi tted with swivel-joint fi ttings Figure 11: Supply/Return Hose Kit at one end to prevent kinking during installation.
Hose kits are available from ClimateMaster in different treatment and fi ltering will be necessary. confi gurations as shown in Figure 12 for connection between the unit and the piping system.
20 mesh] size. The ClimateMaster Water Quality Table provides water quality requirements for ClimateMaster coaxial heat exchangers. The water should be evaluated by an Rev.: 5/6/2014 S independent testing facility comparing to this Table and when properties are outside of these requirements, an external secondary heat exchanger must be used to isolate the heat pump heat exchanger from the unsuitable water.
Figure National Electrical Code as well as all applicable local 16. Most ClimateMaster units are shipped on the medium codes. Refer to the unit electrical data for fuse sizes. speed tap. Consult submittal data or engineering design Consult wiring diagram for fi...
10°F [-12.2°C] refrigerant temperature, a more suitable Maintenance) manual for units with DDC controls. temperature when using an antifreeze solution. All ClimateMaster units operating with entering water Figure 17: TR Low Voltage Field Wiring temperatures below 60°F [15.6°C] must include the...
Figures 20 and 21 illustrate typical slow closing water control valve wiring for Taco 500 series (ClimateMaster P/N AVM) and Taco SBV series valves. Slow closing valves take approximately 60 seconds to open (very little water will fl ow before 45 seconds).
Connection to DXM Control wiring connections should be determined from the thermostat IOM and or unit wiring diagram. Practically Thermostat any heat pump thermostat will work with ClimateMaster units, provided it has the correct number of heating and Compressor cooling stages.
LT2 of 30°F or 10°F [-1°F or -12°C] (refrigerant temperature). Note: This jumper should only be Table 5b: DXM LED And Alarm Relay Operations clipped under extenuating circumstances, as recommended by ClimateMaster technical Status LED Test LED Fault LED...
Page 47
T H E S M A R T S O L U T I O N F O R E N E R G Y E F F I C I E N C Y Tr a n q u i l i t y ( T R ) S e r i e s ®...
The DXM control board will bring the unit on in 2nd Stage cooling/heating modes are like any other ClimateMaster Heating. When the call is satisfi ed at the thermostat WSHP. The reversing valve (“O” signal) is energized in...
Page 51
T H E S M A R T S O L U T I O N F O R E N E R G Y E F F I C I E N C Y Tr a n q u i l i t y ( T R ) S e r i e s ®...
Page 52
C L I M A T E M A S T E R W A T E R - S O U R C E H E A T P U M P S Tr a n q u i l i t y ( T R ) S e r i e s ®...
fi lling the system, for ClimaDry to operate properly. Note: The manufacturer strongly recommends all 4. Verify that all strainers are in place (ClimateMaster piping connections, both internal and external to the recommends a strainer with a #20 stainless steel unit, be pressure tested by an appropriate method wire mesh).
If temperature is within 5. Two factors determine the operating limits range, proceed with the test. If temperature is of ClimateMaster heat pumps, (a) return air outside of the operating range, check refrigerant temperature, and (b) water temperature. When any pressures and compare to table 8.
Page 58
C L I M A T E M A S T E R W A T E R - S O U R C E H E A T P U M P S Tr a n q u i l i t y ( T R ) S e r i e s ®...
ClimateMaster works continually to improve its products. As a result, the design and specifi cations of each product at the time for order may be changed without notice and may not be as described herein. Please contact ClimateMaster’s Customer Service Department at 1-405-745-6000 for specifi c information on the current design and specifi...
Need help?
Do you have a question about the Tranquility TRH 006 and is the answer not in the manual?
Questions and answers