Sony SRG-A40 Command List page 18

Number in ( ) is MENU display values.
Command Set
PAN TILT PAN TILT DRIVE
RAMP CURVE
PAN-TILT SLOW
PAN TILT LIMIT
PRESET RESET
SET
RECALL
SPEED
CALL MODE
PTZ Auto START/STOP
Framing
*
Refer to the section of the Pan/Tilt Position of VISCA Command Setting Values.
Command
Up 8x 01 06 01 vv ww 03 01
FF
Down 8x 01 06 01 vv ww 03 02
FF
Left 8x 01 06 01 vv ww 01 03
FF
Right 8x 01 06 01 vv ww 02 03
FF
UpLeft 8x 01 06 01 vv ww 01 01
FF
UpRight 8x 01 06 01 vv ww 02 01
FF
DownLeft 8x 01 06 01 vv ww 01 02
FF
DownRight 8x 01 06 01 vv ww 02 02
FF
Stop 8x 01 06 01 vv ww 03 03
FF
ABS 8x 01 06 02 vv 00 0p 0p
(Absolute 0p 0p 0t 0t 0t 0t FF
Position)
REL (Relative 8x 01 06 03 vv 00 0p 0p
Position) 0p 0p 0t 0t 0t 0t FF
Home 8x 01 06 04 FF
Reset 8x 01 06 05 FF
- 8x 01 06 31 0p FF
On/Off 8x 01 06 44 0p FF
Limit Set 8x 01 06 07 00 0q 0p 0p
0p 0p 0t 0t 0t 0t FF
Limit Clear 8x 01 06 07 01 0q 07 0F
0F 0F 07 0F 0F 0F FF
Reset 8x 01 04 3F 00 pp FF
Set 8x 01 04 3F 01 pp FF
Recall 8x 01 04 3F 02 pp FF
Select 8x 01 7E 04 1B 0p FF
Separate 8x 01 7E 01 0B pp qq FF
Common 8x 01 7E 04 1C 0p 0p FF
- 8x 01 7E 04 3B 0p FF
- 8x 01 7E 04 3A 0p FF
Command Packet
vv: Pan speed 01 (Slow) - 18 (Fast)
ww: Tilt speed 01 (Slow) - 17 (Fast)
vv: Pan speed 01 (Slow) - 18 (Fast)
ww: Tilt speed 01 (Slow) - 17 (Fast)
vv: Pan speed 01 (Slow) - 18 (Fast)
ww: Tilt speed 01 (Slow) - 17 (Fast)
vv: Pan speed 01 (Slow) - 18 (Fast)
ww: Tilt speed 01 (Slow) - 17 (Fast)
vv: Pan speed 01 (Slow) - 18 (Fast)
ww: Tilt speed 01 (Slow) - 17 (Fast)
vv: Pan speed 01 (Slow) - 18 (Fast)
ww: Tilt speed 01 (Slow) - 17 (Fast)
vv: Pan speed 01 (Slow) - 18 (Fast)
ww: Tilt speed 01 (Slow) - 17 (Fast)
vv: Pan speed 01 (Slow) - 18 (Fast)
ww: Tilt speed 01 (Slow) - 17 (Fast)
vv: Pan speed 01 (Slow) - 18 (Fast)
ww: Tilt speed 01 (Slow) - 17 (Fast)
vv: Pan-Tilt speed 01 (Slow) - 18 (Fast)
pppp: Pan-coordinate*
tttt: Tilt-coordinate*
vv: Pan-Tilt speed 01 (Slow) - 18 (Fast)
pppp: Pan-shift amount*
tttt: Tilt-shift amount*
p: Acceleration and deceleration curve
1=Sharpness
p: 2=On, 3=Off
q: Position (1=UpRight, 0=DownLeft)
For pppp and tttt, refer to the section of the
Pan/Tilt Position of VISCA Command
Setting Values
q: Position (1=UpRight, 0=DownLeft)
pp: PRESET No. to reset - 1 (00 - 63)
pp: PRESET No. to set - 1 (00 - 63)
pp: PRESET No. to recall - 1 (00 - 63)
p: 0=Compatible (specify the speed with
the same command as Separate for VISCA,
and with an argument of the Preset Recall
command for CGI), 1=Separate (operation
with individual speed by a preset),
2=Common (operation with common speed
to all presets)
pp: PRESET No. -1 (00 - 63)
qq: Positioning speed (01 - 19)
pp: Common Speed (01-19)
p: 2=Freeze (Freeze the image from a
camera during recalling), 3=Normal
p: 1=Start, 0=Stop
18
Comments