Page 2
COM Express Specification Reference • Shielded interface cables must be used in order to comply with the emission limits. PICMG® COM Express® Module Base Specification. http://www.picmg.org/ User's Manual | TGH960...
Page 4
• To reduce the risk of electric shock, unplug the power cord before removing the sys- tem chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power cord. User's Manual | TGH960...
Page 5
• Storage devices such as hard disk drive, etc. You will also need external system peripherals you intend to use which will normally include at least a keyboard, a mouse and a video display monitor. User's Manual | TGH960...
1 x Intel® I225 series (10/100/1000Mbps/2.5G) 4 x USB 3.2 Gen2 8 x USB 2.0 SATA 4 x SATA 3.0 (up to 6Gb/s) Support RAID 0/1 1 x 8-bit DIO (Default 4 inputs and 4 outputs) User's Manual | TGH960...
Page 7
Operating: 0 to 60°C, -40 to 70°C Storage: -40 to 85°C Humidity Operating: 5 to 90% RH Storage: 5 to 90% RH MTBF MECHANICAL Dimensions COM Express Basic 95mm (3.74") x 125mm (4.9") ® Compliance PICMG COM Express® R3.0, Type 6 User's Manual | TGH960...
EHL9A2 is a COM Express Mini. The dimension is 84mm x 55mm. Common for all Form Factors Extended only Basic only Compact only Compact and Basic only Mini only 106.00 Extended 91.00 Compact Basic 70.00 51.00 Mini 18.00 6.00 4.00 0.00 User's Manual | TGH960...
Chapter 3 - Hardware Installation X Board Layout X Connector The COM Express connector is used to interface the TGH960 COM Express board to a carrier board. Connect the COM Express connector (located on the solder side of the board) to the CPU fan COM Express connector on the carrier board.Refer to the following pages for the pin functions...
Module SATA3_RX- I SATA AC coupled on AC Coupling capacitor Module ATA_ACT# I/O CMOS 3.3V / 3.3V Connect to LED and recommend current limit resistor 220Ω to 3.3V ATA (parallel and serial) activity indicator, active low. User's Manual | TGH960...
Connect AC Coupling Capacitors 0.1uF to Device DDI2_PAIR2- Module Connect AC Coupling Capacitors 0.1uF to Device DDI2_PAIR3+ DP2_LANE3+ for DP / TMDS2_CLK+/- O PCIE AC coupled off Connect AC Coupling Capacitors 0.1uF to Device DDI2_PAIR3- Module User's Manual | TGH960...
USB differential pairs 7, USB7 may be configured as a USB client or as a host, or both, at the Module Connect 90Ω @100MHz Common Choke in series and ESD suppressors to GND to USB I/O USB 3.3V Suspend/3.3V USB7- connector designer's discretion.(CR901-B default set as a host) User's Manual | TGH960...
Connect to DDC clock of LVDS panel I2C clock output for LVDS display use LVDS_I2C_DAT I/O OD CMOS 3.3V / 3.3V PU 2.2K to 3.3V Connect to DDC data of LVDS panel I2C data line for LVDS display use User's Manual | TGH960...
System Management Bus bidirectional data line. System Management Bus Alert – active low input can be used to SMB_ALERT# I CMOS 3.3V Suspend/3.3V PU 2.2K to 3V3_DU_EC generate an SMI# (System Management Interrupt) or to wake the system. User's Manual | TGH960...
(Recommend add Protecting Logic Level Signals on Pins Reclaimed from VCC_12V) Trusted Platform Module (TPM) Physical Presence pin. Active high. TPM chip has an internal pull down. This signal is used to indicate Physical Presence to the TPM. TPM_PP I CMOS 3.3V / 3.3V PD 10K User's Manual | TGH960...
The carrier board (COM335) used in this section is for reference purpose only and The COM Express connector is used to interface the TGH960 COM Express board to a carrier may not resemble your carrier board. These illustrations are mainly to guide you on board.
These illustrations are for reference only. 1. COMe-LINK2 is the COM Express debug platform installed into COM Express Mini modules for the application of debugging and displaying signals and codes. COM Express Connector COM Express Connector User's Manual | TGH960...
COM Express Type Display Signal Display COM Express Power/Reset/ Power Display Bolts Sleep/LID control 4. Use the provided bolts to fix the COMe-LINK2 debug card onto the carrier board. Cable COMe-DEBUG COMe-LINK2 Bolts COMe-LINK2 Carrier Board COMe-DEBUG User's Manual | TGH960...
Page 27
6. Then, grasp the heat sink by its edges and position it down firmly on the top of the COM Express Mini module. Cable Carrier Board COM Express Mini Module COMe-LINK2 Side View of the Module, Debug Card and Carrier Board COMe-DEBUG User's Manual | TGH960...
“Press DEL to run setup” will appear on the screen. If the message that field and press <Enter>. disappears before you respond, restart the system or press the “Reset” button. You may also restart the system by pressing the <Ctrl> <Alt> and <Del> keys simultaneously. User's Manual | TGH960...
The time format is <hour>, <minute>, <second>. The time is based on the 24-hour military-time clock. For example, 1 p.m. is 13:00:00. Hour displays hours from 00 to 23. Minute displays min- utes from 00 to 59. Second displays seconds from 00 to 59. User's Manual | TGH960...
Enables this field for Windows XP and Linux which are optimized for Hyper-Threading technol- ogy. Select disabled for other OSes not optimized for Hyper-Threading technology. When dis- abled, only one thread per enabled core is enabled. Enable/Disable AES (Advanced Encryption Standard) User's Manual | TGH960...
Disable Turbo GT frequency Enabled: Disables Turbo GT frequency. Disabled: GT frequency is not limited C states Enable or disable CPU Power Management. It allows CPU to enter "C states" when it’s not 100% utilized. User's Manual | TGH960...
This section is used to configure Intel(R) Active Management Technology Parameters. Please refer to the following pages. ME Unconfig on RTC Clear When disabled, ME will not be unconfigured on RTC Clear. Firmware Update Configuration Please refer to the following pages. User's Manual | TGH960...
Note: The configuration must match the specifications of your LCD Panel in order for the LCD Panel to display properly. Note: It might cause system hang-up when disable EDID emulation with PTN3460 chip on the board. User's Manual | TGH960...
Serial Port 1 Configuration Set Parameters of Serial Port 1 (COMA) Serial Port 2 Configuration Set Parameters of Serial Port 2 (COMB) Note: The sub-menus are detailed in following sections. Serial Port Enable or disable serial port. User's Manual | TGH960...
Chapter 4 BIOS SETTINGS Advanced Serial Port Console Redirection Console Redirection By enabling Console Redirection of a COM port, the sub-menu of console redirection settings will become available for configuration as detailed in the following. User's Manual | TGH960...
With this mode enabled only text will be sent. This is to capture Terminal data. Resolution 100x31 Enables or disables extended terminal resolution. Putty Keypad Select FunctionKey and KeyPad on Putty. • VT100 • LINUX • XTERMR6 • • ESCN • VT400 User's Manual | TGH960...
Maximum time the device will take before it properly reports itself to the Host Device power-up delay : Controller.'Auto' uses default value: for a Root port it is 100 ms, for a Hub port the delay is taken from Hub descriptor. User's Manual | TGH960...
Set the wait time in seconds to press ESC key to abort the PXE boot. Use either +/- or numeric keys to set the value. Media detect count Set the number of times the presence of media will be checked. Use either +/- or numeric keys to set the value. User's Manual | TGH960...
▼ CPU/SYS Smart Fan Mode = [Manual Mode] Fix Fan Speed Count Set the fan speed, the value ranging from 1-100%, 100% being full speed. The fans will al- ways operate at the specified speed regardless of gauged temperatures. User's Manual | TGH960...
Please select a submenu and press Enter. The submenus are detailed in the following pages. Memory Configuration Memory Configuration Parameter. Graphics Configuration Settings about graphic. VMD setup menu VMD Configuration Settings PCI Express Configuration : VT-d VT-d capability. X2APIC Opt Out Enable/Disable X2APIC_OPT_OUT bit DMA Control Guarantee Enable/Disable DMA_Control_Guarantee bit User's Manual | TGH960...
Rapid Storage Technology 】 ® Enable VMD Controller Enable/Disable to VMD controller. Enable VMD Global Mapping Enable/Disable to Enable VMD Global Mapping. Note: Intel Rapid Storage Technology will appear in Advanced menu when ® enabled VMD global mapping. User's Manual | TGH960...
2048MB aperture. To use this feature, please disable CSM Support. DVMT Pre-Allocated Select DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used by the Internal Graphics Device. DVMT Total Gfx Mem Select DVMT5.0 Total Graphic Memory size used by the Internal Graphics Device. User's Manual | TGH960...
PCI Express Configuration Settings PCI Express Root Port 9~12, 17~20 & Intel i225 SATA And RST Configuration Control the PCI Express Root Port. SATA Device Otpions Settings HD Audio Configuration HD Audio Subsystem Configuration Settings User's Manual | TGH960...
This field is used to select SATA speed generation limit: Auto, Gen1, Gen2 or Gen3. • Enabled HDA will be unconditionally enabled. SATA Mode Selection The mode selection determines how the SATA controller(s) operates. • AHCI This option allows the Serial ATA controller(s) to use AHCI (Advanced Host Controller Interface). User's Manual | TGH960...
Clear the database from the NVRAM, including all the keys and signatures installed in the Key Management menu. Press Enter and a prompt will show up for you to confirm. Key Management Enables expert users to modify Secure Boot Policy variables without full authentication. User's Manual | TGH960...
“Quiet Boot” is set to enabled, “BGRT Logo” will show up for configura- this field to restore set-ting from the USB flash device. tion. Refer to the Advanced > CSM Configuration submenu for more information. User's Manual | TGH960...