Related Manuals for Hyundai HTDT5324
Summary of Contents for Hyundai HTDT5324
- Page 1 LAWN MOWER PETROL HTDT5324 ORIGINAL INSTRUCTIONS WARNING: Read thoroughly the instruction manual before use.
-
Page 2: Table Of Contents
CONTENTS 1. SAFETY INSTRUCTIONS 2. YOUR PRODUCT 3. ASSEMBLY 4. FILLING FUEL TANK 5. USE 6. MAINTENANCE AND STORAGE 7. EC DECLARATION 8. WARRANTY 9. PRODUCT FAILURE 10. WARRANTY EXCLUSIONS... -
Page 3: Safety Instructions
1. SAFETY INSTRUCTIONS Instructions Read the instructions carefully. Be familiar with the controls and proper use of the equipment. Never allow children to use this mower. If the mower is given to an other people, also give this manual. Also make sure that this person uses this device only after receiving the necessary instructions. - Page 4 Avoid using the equipment on greasy grass, where possible. Always be sure of your walking on the slopes. Walk, never run. For lawn mowers, mow across slopes, never from top to bottom. Exercise extreme caution when changing direction on slopes. ...
- Page 5 disabled; The operator should not alter or tamper with any sealed adjustments for the engine speed control. Maintenance and storage Check and tighten all bolts and screws to ensure that the equipment is in safe operating condition. Never keep the mower with gasoline in the tank in a building or vapours can cause a bright flame or spark.
- Page 6 for repair if necessary. If the mower vibrates abnormally, try to understand the reason and bring your lawnmower to an authorized repair center. Regularly check that the bolts, nuts and screws are properly tightened for safe use of the mower. ...
- Page 7 Follow strictly the instructions in this manual for filling the tool with fuel. During maintenance and storage Switch off the tool and wait until it stops completely. Make sure that all moving parts are stopped. Allow the machine to cool before performing inspection, adjustments, maintenance, servicing and storage.
- Page 8 Danger! Keep your hands and feet away from the cutting element Warning – Exhaust gas. Do not be exposed to exhausted gas and do not use the tool in a confined place Fuel is flammable, keep it away from fire. Do not add fuel while the machine is running During repair work, remove the spark plug and repair according to the operating manual...
-
Page 9: Your Product
2. YOUR PRODUCT a. Description 1. Upper bar Side discharger cover 2. Engine control bar 8.Fall opening Primer bulb Flap 4.Dashboard 10. Grass catcher 5. Engine 11. Self-propeller bar 6. Carter 12.Cutting height lever... - Page 10 TECHNICAL DATA Model HTDT5324 Nominal power 3.2kW Displacement 223cm³ Max engine speed 2850/min Max torque 11.1 Nm Cutting height 25-65mm, 8 positions Cutting width 525mm Volume of the collection bag Weight 36.5kg Engine type RV225 Blade type DY0702-4A Fuel tank capacity...
- Page 11 the right side of the handle) with the two nuts and their screws. Secure the cables with the rubber supports. c) Grass catcher NOTE: When installing the grass catcher, the side discharge and the rear discharge must not be installed. To install: Lift the flap and hang the collection bag on the back of the mower.
-
Page 12: Assembly
e) Back discharge NOTE: When installing the rear discharge, the side discharge and the grass catcher should not be installed. Remove the grass catcher if it is installed. Lift the flap. Fully insert the discharge into the back of the tool. Press the kit to lock it in place. -
Page 13: Filling Fuel Tank
Setting of the cutting height According operation to be performed, adjust the desired cutting height(25- 65mm, 8 positions); Grasp the lever, pull it to the right and then lower it to decrease the cutting height or raise it to increase the cutting height 4. - Page 14 Fuel must meet the following criteria: Clean, new and lead-free gasoline. A minimum octane rating of 87/87 AKI (91 RON). A gasoline containing up to 10% ethanol is acceptable. Remove the fuel tank cap. Add fuel. Close the fuel tank with the cap. Do not overfill.
-
Page 15: Use
5. USE a. Starting the tool This lawn mower can be started manually. Push the primer bulb (3) several times before cool starting. Take the starter rope with your right hand and pull slowly until you have resistance, then pull hard on the starter rope. (If the cold start is not sufficient, repeat this operation 2 or 3 times). -
Page 16: Maintenance And Storage
6. MAINTENANCE AND STORAGE Before working on the cutting system of the machine, switch off the engine and remove the spark plug’s cap. a. Cleaning the mower Cut grass is damp. Regular cleaning after each use will ensure better functioning of the mower and reduce the risk of corrosion or seizure. Having finished mowing, allow the engine to cool then remove accumulated grass clippings from and around the engine with a brush. - Page 17 To remove the blade, loosen the screw, check the blade bracket, and replace all parts if they are worn or damaged. When reassembling the blade, make sure that the cutting edges are in the same direction as the direction of rotation of the motor. The tightening torque of the blade screw should be 3.7 kg * m / s 2 (37 Nm) and can be checked with a torque wrench.
- Page 18 Before transporting the mower Thoroughly clean the mower. Empty the fuel tank using a suction pump. Dispose of discarded fuel safely and responsibly, remembering that petrol vapours can cause explosion or fire. Run the engine until any remaining fuel is consumed. Allow the engine to cool.
- Page 19 Position the blade on its support with the cooling fins facing the engine. Check the correct alignment and matching of pads with the blade. The blade must be positioned precisely on its stand. Tighten the screws connecting all of the components. Make a final visual check that all parts are present and aligned before tightening the fixing bolt very firmly with a wrench while holding the blade firmly in one hand (NB wear suitable gloves).
- Page 20 cleaned with a vacuum cleaner. If it is dirty or contaminated with oil or petrol, replace it. Clean the cover and inside of the air box with a clean cloth. Evenly apply a thin layer of oil to the outside of the cartridge filter with a brush (you can use clean engine oil for this).
- Page 21 Builder SAS 32, rue Aristide Bergès -Z1 31270 Cugnaux - France Tel. +33 (0) 5.34.502.502 Fax: +33 (0) 5.34.502.503 Declares that the machine named below LAWN MOWER PETROL HTDT5324 Serial number: 20201250248-20201250459 Complies with the following European Directives: Machinery Directive 2006/42/EC...