Subscribe to Our Youtube Channel
Related Manuals for Hougen HMD928
Summary of Contents for Hougen HMD928
- Page 1 HMD928 POWER FEED MAGNETIC DRILL OPERATOR’S MANUAL FOR USE WITH “12,000-SERIES” HOUGEN CUTTERS CUTTERS ® ® ®...
-
Page 2: Welcome To Hougen
No other expressed warranty is given or authorized. Hougen Manufacturing, Inc. disclaims any implied warranty of MERCHANTABILITY or FITNESS for any period beyond the expressed warranty and shall not be liable for incidental or consequential damages. -
Page 3: Table Of Contents
Complete and mail the Product Registration Card now. 8. Your Magnetic Drill was factory adjusted prior to It is important that Hougen Manufacturing, Inc. have a shipping. Check to make sure that all gib record of product ownership. -
Page 4: Safety Instructions
12. Non-Conforming Cutting Tools Keep Work Area Clean Your Mag Drill is designed to use Hougen Cutters. Cluttered areas and benches invite injuries. The use of drilling tools having different shank styles Keep dirt and chips from under the Cutter area. -
Page 5: Safety Switch Indicator Light
The Safety Switch Indicator Light is a Standard Safety manual. Do not operate tool if switch does not turn Feature on HMD928 magnetic drills. Its purpose is to inform it on and off. the user that an unsafe condition exists. - Page 6 OPERATION OF CONTROLS BEFORE INSTALLING HOUGEN CUTTER IMPORTANT: Before turning on the machine, it is important that the operator understands the interrelated functions of the SAFETY SWITCH, MAGNET SWITCH, AND MOTOR SWITCH. READ SAFETY SWITCH INDICATOR LIGHT INSTRUCTIONS PREVIOUS PAGE.
-
Page 7: Operating Instructions
OPERATING INSTRUCTIONS Always remember that the magnet’s holding power is directly related to the workpiece thickness and surface condition. Since magnetic attraction diminishes with thinner material or rough surfaces, mechanical clamping of drill unit to the workpiece should be used when cutting thin material (9.5mm or less) or material with uneven surfaces. -
Page 8: Cutting Fluid Reservoir
4. Insert proper pilot in shank end of Hougen Cutter. 5. Insert Hougen Cutter until fl at on cutter shank is aligned with set screw holes and is exactly perpendicular to axis of set screw holes. -
Page 9: Arbor & Gibs Adjustment
ADJUSTMENT OF GIBS 1. Loosen all Gib Screws. 2. Feed the drill in and out a few times and then, with top of motor slide fl ush with top of housing, tighten the Gib Screws until you feel them touch the Steel Gib. 3. - Page 11 MOTOR ASSEMBLY 04042 19048 10538 11053 75289 04502 19033 MOTOR PARTS LIST Part # Description Part # Description 04042 Label, Motor Safety 17614 Gear Housing 04502 Brush Cover 17616 Spindle 05462 Hex Spindle 17617 Fan Guide 10538 Washer #8 17618 Gasket 11053 Screw BHS #8-32...
- Page 12 CONTROL PANEL PARTS LIST Panel Assembly P/N: 19043 19049 05288 05355 05335 05332 05331 04891 Part # Description 19039 04671 Rocker Switch 05318 04877 Wire Harness 05320 04878 LED Spacer 05319 04879 LED Lens 05289 04881 LED Bulb 04891 Stand Off 05288 Power Circuit Board 04671...
- Page 13 CONTROL PANEL HOOKUP...
- Page 14 19033 19018 05187 05203 **10538 **11053 05057 02411 19042 05480 04157 90064 ** INCLUDES THESE PARTS 02423 41044 02422 04500 **04391 10560 50035 75156 02429 10553 40302 02428 ����� 40301 40300 90028 90077 40295 40332 40300 ����� 40301 40303 10560 40237 40302 40038...
- Page 15 05059 05061 HMD928 05060 Exploded View HOOKS TO COOLANT INDUCER ����� ����� ����� ����� ����� ����� ����� ����� ����� ����� ����� ����� ����� ����� ����� ����� ����� ����� ����� ����� ����� ����� ����� ����� ����� ����� ����� ����� ����� �����...
- Page 16 HMD928 PARTS LIST Part # Description Part # Description 01165 Retaining Ring 05471 Arbor Assy 02217 SCR-SOC #8-32 05628 Set Screw 1/4 - 28 x 3/8 02411 Strain Relief-Motor Cord 05480 Motor Assy 02422 Bracket-Motor Cord 10506 SCR-Set 3/8-24 02423...
- Page 17 HMD928 PARTS LIST CONT. Part # Description 40038 SCR-SHC #10-32 40077 SCR-SHC 1/4-20 40234 Thrust Washer 40237 SCR-SS 1/4-28 40277 Roll Pin 40295 Inducer 40300 O-Ring 40301 Washer 40302 Retaining Ring 40303 Tube Fitting 40332 Inducer Assy 40398 Retaining Ring...
- Page 18 MAINTENANCE In order to minimize wear on moving parts and to insure smoother operation and longer life for your magnetic drill, the following maintenance should be done periodically, based on use. 1. Regularly tighten all fasteners and replace all worn parts. 2.
- Page 19 HINTS FOR SMOOTHER OPERATION 1. Keep inside of Hougen Cutter clear of chips. Chips will interfere with cutting to maximum depth and may impede the free oil fl ow and can cause cutter breakage. 2. Keep work, machine, arbor and Hougen Cutter free of chips and dirt.
Need help?
Do you have a question about the HMD928 and is the answer not in the manual?
Questions and answers