Related Manuals for Badger Meter Blancett B3100
Summary of Contents for Badger Meter Blancett B3100
- Page 1 Blancett B3100 Flow Monitor Page 1 B3100 Flow Monitor TUTORIAL AUTOMATIC UNIT CONVERSION DSY-UM-02266-EN-02 (May 2021) DSY-UM-02266-EN-02_B3100 Automatic Unit Converter Tutorial.docx...
- Page 2 Blancett B3100 Flow Monitor Page 2 This E112-series tutorial is created to provide as accurate and authoritative information regarding the subjects covered as was available at the time of writing. The copyright owner of this E112-series tutorial cannot take any responsibility or liability for any errors or...
-
Page 3: Table Of Contents
Blancett B3100 Flow Monitor Page 3 Table of content DESCRIPTION OF THE AUTOMATIC UNIT CONVERSION ..........4 The relation between the K-Factor and the automatic unit conversion ........4 The relation between the K-Factor and the measurement unit set by hand ......4 HOW TO SETUP THE AUTOMATIC UNIT CONVERSION ........... -
Page 4: Description Of The Automatic Unit Conversion
Blancett B3100 Flow Monitor Page 4 1 Description of the automatic unit conversion The automatic unit conversion is a feature that helps you to avoid the different K-Factor calculations for the (accumulated) total and the flowrate. With the automatic unit conversion, you only need the test/calibration certificate that came with your flowmeter. -
Page 5: How To Setup The Automatic Unit Conversion
Blancett B3100 Flow Monitor Page 5 2 How to setup the automatic unit conversion This chapter explains the procedure how to setup the automatic unit conversion. 2.1 How to set the K-Factor (units) for the flowmeter For easy access the procedure gives the action (what to do), the result (how the B3100 will respond) and a notice to give additional information to make the procedure more easy to do. - Page 6 Blancett B3100 Flow Monitor Page 6 ACTION RESULT OTICE 10. Press the ▲ button to Read the unit from the flowmeter • The m selection shows make the required certificate and select the same (the flowmeter is selection. measurement unit in this menu.
-
Page 7: The Automatic Unit Conversion - Hand Mode
Blancett B3100 Flow Monitor Page 7 2.1.2 The automatic unit conversion - HAND mode This procedure gives the information how to setup the HAND mode. The HAND mode is selected when the required measurement unit is not supported by the automatic unit conversion. - Page 8 Blancett B3100 Flow Monitor Page 8 ACTION RESULT OTICE 12. Press the ▲ button to • The selection US GAL For the explanation, make the required shows. the measurement unit for the selection. (accumulated) total is set to US GAL.
-
Page 9: The (Accumulated) Total - Hand Mode
Blancett B3100 Flow Monitor Page 9 2.2.2 The (accumulated) total - HAND mode This procedure gives the information how to setup the HAND mode. The HAND mode is selected when the required measurement unit is not supported by the automatic unit conversion. - Page 10 Blancett B3100 Flow Monitor Page 10 ACTION RESULT OTICE 11. Press the PROG button momentarily. Now you can set the calculated • The PROG K-Factor for the (accumulated) indicator total. comes on. 12. Use the ▲ button and the ► button to •...
-
Page 11: Set The Reading For The Flow Rate
Blancett B3100 Flow Monitor Page 11 2.3 Set the reading for the flow rate This chapter explains the procedure how to setup the measurement unit for reading the B3100. 2.3.1 The flow rate - AUTO-VOL and AUTO MAS mode This setting does not influence the K-Factor measurement unit as set from the flowmeter certificate. - Page 12 Blancett B3100 Flow Monitor Page 12 NOTICE The K-Factor and the K-Factor decimals for the flow rate shows as AUTO because the automatic unit conversion controls these parameters. ACTION RESULT OTICE 14. Press the ▲ button until The flow rate is calculated by •...
-
Page 13: The Flow Rate - Hand Mode
Blancett B3100 Flow Monitor Page 13 2.3.2 The flow rate - HAND mode This procedure gives the information how to setup the HAND mode. The HAND mode is selected when the required measurement unit is not supported by the automatic unit conversion. - Page 14 Blancett B3100 Flow Monitor Page 14 ACTION RESULT OTICE 14. Press the ▲ button until Calculate the K-Factor for the • The K-FACTOR menu the K-FACTOR menu (accumulated) total by hand and shows. shows. make a note. 15. Press the PROG button Now you can set the calculated •...
- Page 15 Blancett B3100 Flow Monitor Page 15 ACTION RESULT OTICE 27. Press the PROG button Now you can set the cut-off time in • The PROG indicator momentarily. seconds. comes on. 28. Press the ▲ button and • The selection 15.0 shows. For the explanation, the ►...
-
Page 16: The Linearization Function
Blancett B3100 Flow Monitor Page 16 3 The linearization function This chapter gives an description and explains the procedure how to setup the linearization. 3.1 Description of the linearization The linearization function is used to make the reading of the (accumulated) total, the flow rate, the analog and the pulse output more accurate. -
Page 17: How To Use The Linearization Function
Blancett B3100 Flow Monitor Page 17 3.2 How to use the linearization function This procedure gives the information how to setup the linearization function. The linearization function is applicable for all modes of the automatic unit conversion, AUTO-VOL, AUTO-MAS and HAND. -
Page 18: Disable The Linearization Function
Blancett B3100 Flow Monitor Page 18 ACTION RESULT OTICE 13. Press the PROG button Now you can set the decimal • The PROG indicator momentarily. pointer for the frequency only. comes on. This decimals setting does not change the MF setting. - Page 19 Blancett B3100 Flow Monitor Page 19 DSY-UM-02266-EN-02_B3100 Automatic Unit Converter Tutorial.docx...
- Page 20 Blancett B3100 Flow Monitor DSY-UM-02266-EN-02_B3100 Automatic Unit Converter Tutorial.docx...