Related Manuals for Badger Meter Blancett B114-110
Summary of Contents for Badger Meter Blancett B114-110
- Page 1 Turbine Flow Meter 1100 Series Turbine Meter User Manual TUR-UM-00014-EN-09 (November 2022) 1.888.610.7664 www.calcert.com sales@calcert.com...
-
Page 2: Table Of Contents
Turbine Flow Meters, 1100 Series CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Operating Principle . -
Page 3: Introduction
Introduction INTRODUCTION Designed to withstand the demands of the most rigorous flow measurement applications, the Model 1100 turbine flow meter is reliable, rugged and cost effective . Originally developed for the secondary oil recovery market, the Model 1100 is an ideal meter for liquid flow measurement on or off the oil field . -
Page 4: Specifications
Though the meter is designed to function in any position, where possible, install it horizontally with the conduit adapter facing upward . 3 . Thread a magnetic pickup (Badger Meter model B111109 or equivalent) into the conduit adapter completely finger tight without forcing . Secure with a lock nut if supplied . - Page 5 Severe pulsation and mechanical vibration affect accuracy and shorten the life of the meter . If this condition is present, consider using a flow meter possessing superior resistance to pulsation and vibration like the Badger Meter QuikSert . Do not locate the flow meter or connection cable close to electric motors, transformers, sparking devices, high voltage lines, or place connecting cable in conduit with wires furnishing power for such devices .
- Page 6 Installation Electronic Flow Monitor Isolation and Isolation Valve Flow Rate Control Valve 10 Pipe Turbine 5 Pipe Diameters Flow Meter Diameters Bypass Valve Figure 3: Meter installation with a bypass line Electronic Flow Monitor Control Valve 10 Pipe Turbine 5 Pipe Diameters Flow Meter Diameters...
-
Page 7: Pressure Drop In Water
Pressure drop in water PRESSURE DROP IN WATER Pressure Drop vs Flow Rate Pressure Drop vs Flow Rate 3/8” 3/4” 1” 2” 4” 8” 1/2” 7/8” 1-1/2” 3” 6” 10” 1/2” 7/8” 1-1/2” 3” 6” 10” 3/8” 2” 4” 3/4” 1”... -
Page 8: Turbine Replacement
Turbine replacement TURBINE REPLACEMENT The Model 1100 turbine flow meter uses wear-resistant moving parts to provide trouble-free operation and long service life . Designed for easy field service of a damaged flow meter, Model 1100 repair kits replace only the internal parts, not the entire flow meter . -
Page 9: Disassembly
Turbine replacement Disassembly 1 . Refer to Figure Figure 8 Figure 9 for relative positions of repair kit components . 2 . Remove the magnetic pickup from the meter body to avoid damage during repair . 3 . Remove the retaining ring from one end of the meter . 4 . -
Page 10: New Turbine Kit Installation
Turbine replacement New Turbine Kit Installation MPORTANT Before reassembly, note that an arrow is cast or engraved on each component. The arrow indicates the primary flow direction. When reassembled, the arrowheads must point in the direction of the fluid flow. The arrows must also be oriented in the up position on both rotor supports. -
Page 11: Part Number Information
Part number information PART NUMBER INFORMATION Flow Ranges Approx. Meter Part End Connec- Max. Strainer End to End Bore Size K-factor Weight Number tions Mesh Length gpm (lpm) m3/d Pulse/Gal (lb) 3/8 in . 0 .6…3 3 .00 in . B110-375-½... -
Page 12: Troubleshooting Guide
Control. Manage. Optimize. Blancett is a registered trademark of Badger Meter, Inc . Other trademarks appearing in this document are the property of their respective entities . Due to continuous research, product improvements and enhancements, Badger Meter reserves the right to change product or system specifications without notice, except to the extent an outstanding contractual obligation exists .