Related Manuals for Hachette ALIEN
Summary of Contents for Hachette ALIEN
- Page 1 A L I E N spectacular scale EASY EASY ASSEMBLY ASSEMBLY BUILD THE TERRIFYING XENOMORPH FROM ALIEN PACK 2 KITS 5 - 12...
-
Page 2: B U I L D I N S T R U C T I O N S
Keep away from children. If you suspect a magnet has been swallowed, seek medical help straight away. Hachette Partworks Ltd, 4th Floor, Jordan House, Some parts may have sharp edges, please handle them with care. -
Page 3: Parts Supplied
A S S E M B L Y G U I D E K I T 5 : S K U L L & A P P E N D A G E S In this kit you will continue the assembly of the skull of the Xenomorph and start to fix some of the appendages to the left-hand side. - Page 4 K I T 5 : S K U L L & A P P E N D A G E S EXPERT TIP: Before starting the construction, study the parts photographed carefully to identify each of the skull pipes and lay them out in order. Identify Skull Pipe and test-fit the three tabs along its side into...
- Page 5 K I T 5 : S K U L L & A P P E N D A G E S In a similar way, test-fit the three tabs on Pipe into the slots in Skull part so as to continue from Pipe 5-3. Apply a little glue to the tabs to hold the part firmly in place.
- Page 6 K I T 5 : S K U L L & A P P E N D A G E The line of pipes ends with the tabs on Pipe fitting into the last four slots in Skull 5-1. Again, apply a little glue to the tabs to secure the part firmly in place.
- Page 7 A S S E M B L Y G U I D E K I T 6 : F R O N T- L E F T S E C T I O N O F T H E H E A D In this kit you will start to assemble pieces of the front-left portion of the Xenomorph’s head.
- Page 8 K I T 6 : F R O N T - L E F T S E C T I O N O F T H E H E A D Take the lower jaw assembly from kit Fit the Washer into the opening in the Lower Jaw A 2 and gently remove the Side Panel...
- Page 9 K I T 6 : F R O N T - L E F T S E C T I O N O F T H E H E A D Turn the Head Section around, Finally, apply a little glue to the tabs as shown.
- Page 10 A S S E M B L Y G U I D E K I T 7 : C E N T R E - L E F T S E C T I O N O F T H E H E A D In this kit you will continue to assemble the centre-left side of the Xenomorph’s head and add more appendages.
- Page 11 K I T 7 : C E N T R E - L E F T S E C T I O N O F T H E H E A D Take the Front-left Section of the Head from the last kit along with part 7-1. There are three raised screw sockets (circled) on onto which the round recesses on part fit.
- Page 12 K I T 7 : C E N T R E - L E F T S E C T I O N O F T H E H E A D Turn the assembly over and take the two Pipes which were supplied with the previous kit.
- Page 13 K I T 7 : C E N T R E - L E F T S E C T I O N O F T H E H E A D After test-fitting, apply a little glue to Pipe attach by slotting it over the remaining two rectangular blocks on 7-1.
- Page 14 K I T 7 : C E N T R E - L E F T S E C T I O N O F T H E H E A D Finally, apply a little glue to the tabs on Pipe 7-7. Noting that the widest end of the Pipe sits next to...
- Page 15 A S S E M B L Y G U I D E K I T 8 : F R O N T- R I G H T S E C T I O N O F T H E H E A D In this kit you will start to assemble the parts of the front-right section of the Xenomorph’s head.
- Page 16 K I T 8 : F R O N T - R I G H T S E C T I O N O F T H E H E A D Fit the Washer into Take the Lower Jaw A the opening shown in remove the Side Panel from...
- Page 17 K I T 8 : F R O N T - R I G H T S E C T I O N O F T H E H E A D Turn the Front-right Section of Finally, check that the tabs on the Head around so that it Pipe...
- Page 18 A S S E M B L Y G U I D E K I T 9 : C E N T R E - R I G H T S E C T I O N O F T H E H E A D In this kit you’ll continue building the centre right side of the Xenomorph’s head and adding appendages.
- Page 19 K I T 9 : C E N T R E - R I G H T S E C T I O N O F T H E H E A D Lay the Centre-right Section of the Head upside down on the work surface and note the three raised screw sockets at one end (circled).
- Page 20 K I T 9 : C E N T R E - R I G H T S E C T I O N O F T H E H E A D Turn the assembly over and take the two Pipes from the previous kit.
- Page 21 K I T 9 : C E N T R E - R I G H T S E C T I O N O F T H E H E A D Repeat the previous step to fit the remaining Pipe over the rectangular blocks at the end of Head Section 9-1.
- Page 22 A S S E M B L Y G U I D E K I T 1 0 : T H E H E A D A N D N E C K In this kit you will continue the assembly of the head and its appendages and start to assemble the first parts of the neck.
- Page 23 K I T 1 0 : T H E H E A D A N D N E C K Take the Centre-right Head assembly from the previous kit. After checking the fit, apply a little glue to the tabs of Pipe 10-1 fit them, as shown, into the slots in the Head section 9-1.
- Page 24 K I T 1 0 : T H E H E A D A N D N E C K 10-5 Slot Washer 10-5 into the central hole in Neck 10-6, as shown. Note that part 10-5 is tapered and the smaller end goes at the bottom of part 10-6.
- Page 25 A S S E M B L Y G U I D E K I T 1 1 : T H E N E C K In this kit you will continue to assemble the pieces that form the neck of the Xenomorph. 11-1 11-2 11-3...
- Page 26 K I T 1 1 : T H E N E C K 11-4 11-2 10-5 10-5 10-6 11-4 10-6 Take Neck parts 10-5 10-6 With the ball end of Rod which were prepared in the previous 11-4 inside the assembly kit.
- Page 27 A S S E M B L Y G U I D E K I T 1 2 : T H E H E A D A N D S K U L L In this kit you will continue to assemble different parts of the head and skull.
- Page 28 K I T 1 2 : T H E H E A D A N D S K U L L Take the ball joint assembly 11-4 12-5 and the Skull Attachment Plate 11-1 from the previous kit along with Head 12-1. Take note of the flat side at the top of the ball joint assembly 11-4...
- Page 29 K I T 1 2 : T H E H E A D A N D S K U L L Take the left head assembly 6-1/7- which was constructed in kit 7. Insert the tab at the side of Head 12-1 (circled) into the slot in the head section...
- Page 30 K I T 1 2 : T H E H E A D A N D S K U L L Take the lower jaw assembly 2-1, which was last worked upon in kit 8, and carefully remove the Lower Laterals Jaws A and B and 2-4.
- Page 31 K I T 1 2 : T H E H E A D A N D S K U L L 12-1 10-4 Turn the head assembly upside down and take Pipes 10-4 which were supplied with kits 7 and 10 respectively. One end of part has a peg which inserts into a hole in part 7-1.
- Page 32 K I T 1 2 : T H E H E A D A N D S K U L L 12-6 Lastly, position the skull assembly, 12-3 last worked on in kit 5, on the work surface. Study the photograph carefully and note how the Lower Jaw Piece 12-3...