Subscribe to Our Youtube Channel
Related Manuals for Motorline professional KVM205
Summary of Contents for Motorline professional KVM205
- Page 1 KVM205-KVM210-KVM215 KVM205 - KVM210 - KVM215 USER/INSTALLER MANUAL v1.2 REV. 01/2023...
-
Page 2: Table Of Contents
00. CONTENT 01. SAFETY INSTRUCTIONS ATTENTION: INDEX 01. SAFETY INSTRUCTIONS This product is certified in accordance with European Community (EC) safety standards. 02. THE AUTOMATION TECHNICAL CHARACTERISTICS This product complies with Directive 2011/65/EU of the PACKAGE European Parliament and of the Council, of 8 June 2011, on MOTOR DIAGRAM the restriction of the use of certain hazardous substances DIMENSIONS OF THE MOTOR AND MANEUVER BOARD... -
Page 3: Safety Instructions
01. SAFETY INSTRUCTIONS GENERAL WARNINGS • Children shouldn’t play with the product or opening devices to avoid the motorized door or gate from being triggered involuntarily. • This manual contains very important safety and usage information. very important. Read all instructions carefully before beginning the WARNINGS FOR TECHNICIANS installation/usage procedures and keep this manual in a safe place that it can be consulted whenever necessary. - Page 4 01. SAFETY INSTRUCTIONS RESPONSABILITY September 2009. • Attach the permanent label for the manual release as close as possible • Supplier disclaims any liability if: to the release mechanism. • Product failure or deformation result from improper installation • Disconnect means, such as a switch or circuit breaker on the electrical use or maintenance! panel, must be provided on the product’s fixed power supply leads in •...
-
Page 5: The Automation
02. THE AUTOMATION 02. THE AUTOMATION TECHNICAL CHARACTERISTICS PACKAGE The KVM205, KVM210 and KVM215 are shaft-driven automations for automating industrial sectional 01• 01 KVM motor 06• 04 Motor fixing screws 02• 01 Maneuver board (with control board) 07• 01 Dowel/key doors, with the possibility of horizontal or vertical application. -
Page 6: Motor Diagram 5A
02. THE AUTOMATION 02. THE AUTOMATION MOTOR DIAGRAM DIMENSIONS OF THE MOTOR AND MANEUVER BOARD 01• Encoder 05• Cable glands 02• Motor thermal protection line 06• Hoist protection switch 03• Motor lead wire 07• Motor power supply line 04• Connectors 08•... -
Page 7: Installation
03. INSTALLATION AUTOMATION INSTALLATION • The gearmotor must be installed in a protected area, without risk of damage. • The fixing surface must be solid. • Appropriate accessories must be used to fix the motor to the fixing surface. • Install pipes suitable for the passage of electrical cables, in order to guarantee full protec- tion against mechanical damage. -
Page 8: Installation Guide 7A
03. INSTALLATION 03. INSTALLATION INSTALLATION GUIDE MC200 CONTROL BOARD Display Main Board R111 Motor OPEN R112 STOP R111 R112 R113 CLOSE KEY-6 R115 R114 R113 R115 R111 R114 R111 OPEN R112 R113 R115 STOP R114 R112 KEY-6 CLOSE R113 R115 Maneuver R114 board with... -
Page 9: Programming
04. PROGRAMMING 04. PROGRAMMING SET THE SETTINGS OF SWITCH FUNCTIONS DISPLAY Number Instructions DIPPER Motor position / Input Code: STOP Menu • Dipper 1 must always be ON • allows access to the programming OPEN set to OFF menu; Operating Mode CLOSE OFF •... -
Page 10: Automatic Closing 9A
04. PROGRAMMING 04. PROGRAMMING AUTOMATIC CLOSING PARAMETER CONFIGURATION (P2-01 a P2-13) 1 • Press and hold the SET button for more than 3 seconds, and the display will show P0. Click on the OPEN button and select the parameter P2. Automatic Closing Manual 2 •... -
Page 11: Parameter Configuration (P3-01 To P3-06) 10A
04. PROGRAMMING 05. TROUBLESHOOTING PARAMETER CONFIGURATION (P3-01 a P3-06) ERRORS MAP 1 • Press and hold the SET button for more than 3 seconds, and the display will show P0. Click on the OPEN CIRCUIT BOARD FAULT CODE - REASON AND SOLUTION button and select the parameter P3. -
Page 12: Connection Scheme
06. CONNECTION SCHEME CONNECTION SCHEME Display Board Motor Encoder Cable MR17 Receiver Control board Central Recetor MR17 * Buttons Board Main board STOP OPEN Green Opening Purple Rose Closing STOP White Yellow KEY-6 CLOSE R111 R112 R113 R115 R114 Photocells Loading dock COM NC Series connection with... -
Page 13: Connection Scheme 11A
06. CONNECTION SCHEME INSTRUCTIONS FOR FINAL CONSUMERS / TECHNICIANS Anomaly Procedure Behavior Procedure II Find the source of the problem 1 • Open the control bord and • Motor does not • Check that the • Still not working • Consult a qualified MOTORLINE technician.
Need help?
Do you have a question about the KVM205 and is the answer not in the manual?
Questions and answers