Subscribe to Our Youtube Channel
Related Manuals for Motorline professional KVM205
Summary of Contents for Motorline professional KVM205
- Page 1 KVM205-KVM210-KVM215 KVM105EV | KVM110EV | KVM115EV USER/INSTALLER MANUAL v1.1 REV. 07/2022...
-
Page 2: Table Of Contents
00. CONTENT 01. SAFETY INSTRUCTIONS ATTENTION: INDEX 01. SAFETY INSTRUCTIONS This product is certified in accordance with European Community (EC) safety standards. 02. THE AUTOMATION TECHNICAL CHARACTERISTICS This product complies with Directive 2011/65/EU of the MANUAL OPENING/CLOSING European Parliament and of the Council, of 8 June 2011, on PACKAGE the restriction of the use of certain hazardous substances MOTOR DIAGRAM... -
Page 3: Safety Instructions
01. SAFETY INSTRUCTIONS GENERAL WARNINGS • Children shouldn’t play with the product or opening devices to avoid the motorized door or gate from being triggered involuntarily. • This manual contains very important safety and usage information. very important. Read all instructions carefully before beginning the WARNINGS FOR TECHNICIANS installation/usage procedures and keep this manual in a safe place that it can be consulted whenever necessary. - Page 4 01. SAFETY INSTRUCTIONS RESPONSABILITY September 2009. • Attach the permanent label for the manual release as close as possible • Supplier disclaims any liability if: to the release mechanism. • Product failure or deformation result from improper installation • Disconnect means, such as a switch or circuit breaker on the electrical use or maintenance! panel, must be provided on the product’s fixed power supply leads in •...
-
Page 5: The Automation
02. THE AUTOMATION 02. THE AUTOMATION TECHNICAL CHARACTERISTICS PACKAGE The KVM205EV, KVM210EV and KVM215EV are shaft-driven automations for automating industrial In the kit you will find this components: sectional doors, with the possibility of horizontal or vertical application. The easy installation, configuration and maintenance makes it ideal for all types of sectional doors. -
Page 6: Motor Diagram 5A
02. THE AUTOMATION 02. THE AUTOMATION MOTOR DIAGRAM DIMENSIONS OF THE MOTOR AND MANEUVER BOARD 01• Encoder 05• Terminal 02• Motor thermal protection line 06• Waterproof connectors 03• Motor lead wire 07• Power line 04• Numerical tube 08• Signal line White Yellow 01•... -
Page 7: Installation
03. INSTALLATION AUTOMATION INSTALLATION • The gearmotor must be installed in a protected area, without risk of damage. • The fixing surface must be solid. • Appropriate accessories must be used to fix the motor to the fixing surface. • Install pipes suitable for the passage of electrical cables, in order to guarantee full protec- tion against mechanical damage. -
Page 8: Installation Guide 7A
03. INSTALLATION 03. INSTALLATION INSTALLATION GUIDE MC200 CONTROL BOARD Display Main Board R111 Motor R112 R113 R111 R115 R112 R114 R111 OPEN R112 R113 R115 STOP R113 R114 KEY-6 CLOSE R115 R114 Maneuver board with MARK THE HOLES control Make a mark on the wall at a distance of 1500mm from the floor. -
Page 9: Programming
04. PROGRAMMING 04. PROGRAMMING SET THE CODE SWITCH SETTINGS BUTTONS OPEN button: used to open the door; OPEN DIPPER STOP button: stops the door movement; STOP CLOSE button: used to close the door. SET button: used to confirm and enter the menus; •... -
Page 10: Course Programming 9A
04. PROGRAMMING 04. PROGRAMMING COURSE PROGRAMMING PARAMETER SETTING MEMORIZE COURSE PARAMETER P2 SETTINGS 1 • Press SET more than 3 seconds, the display will show P0, then press SET, the display will show LO. 1 • Press and hold the SET button for more than 3 seconds, the display will show P0. Click on the OPEN key 2 •... -
Page 11: Troubleshooting
04. PROGRAMMING 05. TROUBLESHOOTING PARAMETER SETTING ERRORS MAP PARAMETER P3 SETTINGS CIRCUIT BOARD FAULT CODE - REASON AND SOLUTION 1 • Press and hold the SET button for more than 3 seconds, the display will show P0. Click on the OPEN but- ton and select parameter P3. -
Page 12: Connection Scheme
06. CONNECTION SCHEME Display Board Motor Encoder Cable MR17 Receptor MR5 Receptor Control board Central Recetor MR17 Recetor MR5 Buttons Board Main board STOP OPEN Green Opening Purple Rose Closing STOP White Yellow KEY-6 CLOSE R111 R112 R113 R115 R114 Photocells Loading dock COM NC... -
Page 13: Connection Scheme 11A
06. CONNECTION SCHEME INSTRUCTIONS FOR FINAL CONSUMERS / TECHNICIANS Anomaly Procedure Behavior Procedure II Find the source of the problem 1 • Open the control bord and 3 • Disconnect the motor from 4 • If the motor works, the 5 •...
Need help?
Do you have a question about the KVM205 and is the answer not in the manual?
Questions and answers