Meiligao (MEITRACK), or transmitted in any form, either electronically or mechanically, including photocopying and recording. In no event shall Meiligao (MEITRACK) be liable for direct, indirect, special, incidental, or consequential damages (including but not limited to economic loss, personal injury, and loss of asset and property) arising out of the use or inability or illegality to use the product or documentation.
Check that the SIM Lock code is turned off; If you require the function of sending an SMS location report to the authorized phone number when it makes a call to the MVT600, please make sure the SIM installed supports displaying caller ID.
External Documentation Flashing (1 second on and 2 seconds off) MVT600 is not connected to the GSM network 6.4 Track by Calling Make a call to MVT600 and it will report with one SMS. For example, Now,110727 02:48,V,16,23Km/h,61%,http://maps.google.com/maps?f=q&hl=en&q=22.540103,114.082329 &ie=UTF8&z=16&iwloc=addr&om=1 Click on the link then the location can be shown directly on Google Maps on your mobile phone.
If no preset phone number, it is empty (default is empty). Send command “0000, A71” to delete all phone numbers. When the SOS button is pressed, MVT600 will make a call to phone number 1, 2 and 3. It will stop calling when one number answers.
File Name: MEITRACK MVT600 User Guide Creator: Cavana Cheung Project: MVT600 Creation Date: 2010-09-13 Update Date: 2011-08-01 Sub Project: User Guide Page: 9 of 22 Revision: V2.0 Confidential: External Documentation Authorize a phone number to make a silent call to the tracker. The tracker will answer the call automatically and allows the caller to listen to what is happening around the tracker.
This part shows you the basics in how to use the MEITRACK Parameter Editor. Note: Don’t connect MVT600 to external battery when configuring. Please refer to the MEITRACK Parameter Editor User Guide for more detailed information regarding configuration and functions.
Confidential: External Documentation Note: Remember this Com number. It needs to be input into the MEITRACK Parameter Editor. It is COM3 in this example and it would be COM4 or COM5… in your computer. Run ‘MEITRACK Parameter Editor.exe’ and the following configuration window will pop up: Choose the correct Com number and terminal type in previous Device Manager then click the ‘Open Port’...
Page 12
File Name: MEITRACK MVT600 User Guide Creator: Cavana Cheung Project: MVT600 Creation Date: 2010-09-13 Update Date: 2011-08-01 Sub Project: User Guide Page: 12 of 22 Revision: V2.0 Confidential: External Documentation Item Description User Password SMS password for sending SMS commands and defaulted as 0000.
Page 13
Event Selected event’s SMS reports will be sent to the authorized phone number. For more details, please refer to MEITRACK GPRS/SMS Protocol. For description of events from SOS/Input 1 Active to Tow Alarm, please refer to tap II GPRS Tracking.
Page 14
External Power Off Alarm when external power supply if off or cut. No GPS Signal Report when MVT600 enters GPS blind area or no GPS signal. Get GPS Signal Report when MVT600 exits GPS blind area or get GPS signal.
Interval = 0, stop tracking by time interval. Max time interval = 65535*10 seconds GPRS Report Times = 0, report without limit. = [1,65535], set report times, MVT600 will stop reporting when reaching the times. IP & Port Input server’s IP address and port number.
Page 16
External Power Off Alarm when external power supply if off or cut. No GPS Signal Report when MVT600 enters GPS blind area or no GPS signal. Get GPS Signal Report when MVT600 exits GPS blind area or get GPS signal.
You can define tow time on tap III Main Settings. RFID RFID data. For more information about GPRS settings, please refer to MEITRACK SMS/GPRS Protocol. 7. Installation 7.1 Install I/O Cable The I/O cable is a 12-pin cable including power, analog input, negative/positive input and output.
File Name: MEITRACK MVT600 User Guide Creator: Cavana Cheung Project: MVT600 Creation Date: 2010-09-13 Update Date: 2011-08-01 Sub Project: User Guide Page: 18 of 22 Revision: V2.0 Confidential: External Documentation 10 (AD2) Blue 12 Bits Resolution Analog Input2. 0~6V DC Detection. It can be used to connect with temperature/fuel sensor etc.
External Documentation Power Output. Output Voltage: 5V Black Ground Yellow RS232 Interface TX (MVT600 RX) Green RS232 Interface RX (MVT600 TX) Note: Micro SD is required for taking photos. 7.1.8 Install Micro SD There’s a Micro SD card slot under the On/Off button. Micro SD card can be used to store the pictures taken by the camera.
Note: Do not shield or cover the GPS antenna with any objects containing metal. 7.3 Mount the MVT600 unit If mounting required, there are 4 screw holes on the MVT600, 2 along either side that act as fixing points to the vehicle Please do not hesitate to email us at info@meitrack.com...