Table of contents SECTION 1: Using these instructions Before you start SECTION 1: Using the instructions ..............3 SECTION 2: IMPORTANT SAFETY INSTRUCTIONS ..........4 This document is a Quick Start Installation Guide. For further details on installing and operating your HydroTap SECTION 3: WARNINGS AND REGULATORY INFORMATION ......7 download &...
SECTION 2: IMPORTANT SAFETY INSTRUCTIONS SECTION 2: IMPORTANT SAFETY INSTRUCTIONS Compliance • High concentration of gas may cause asphyxiation. All Plumbing and Electrical connections must comply with local, • Use only in an upright position. state and federal codes. • The cylinder must be used with the supplied pressure regulator. All Plumbing and Electrical connections must be made in accordance with local •...
Application than 1Ω. Use the power cable supplied. It is the responsibility The HydroTap G5 Home series is intended to be used in household and of the installer to ensure the power point is earthed. similar applications such as: •...
66 (30) (300W) ensure the power supply cord is not trapped or damaged. If the power supply cord is damaged it must be replaced by a Zip service provider or Electricity supply requirements a qualified electrician. 110-120VAC 60Hz or 230VAC 60Hz (for power rating see table above).
Drip tray kit Optional Note: Mains water isolation valve is not supplied with the kit. Contact Zip for the full range of consumables and accessories. Quick Start Installation Guide Quick Start Installation Guide 807120US v1.02 11.22 G5 CS Quick Start Guide...
Page 7
All models (supplied) If cupboard temperature exceeds 95°F, (35°C) additional ventilation is required. Contact your Zip service provider for options (including additional vents and fan kit). Vent tray dimensions WxDxH inch (mm): 19.7 (500) x 20.3-21.8 (515-555) x 1.6 (40)
Connect the water supply SECTION 7: Fit the carbonation valve SECTION 8: Valves and fittings must be sealed with PTFE tape if compression Classic, Wave, Celsius Arc and Cube Avoid seals are not included. Classic Plus, Elite Plus Note Mixer faucet installations also use a ‘Tee piece’ as part of the water supply plumbing connections, see the Faucet installation instructions supplied with the Mixer to connect the water supply if using the mixer faucet option.
SECTION 9: Install the CO2 cylinder and regulator SECTION 9: Install the CO2 cylinder and regulator Be aware of the risks of hazards which Do not proceed if the seals are damaged. could cause harm when handling Take care not to cross thread the regulator, a cross threaded compressed CO2.
SECTION 9: Install the CO2 cylinder and regulator SECTION 10: Connect the Command Center Adjust the G5 regulator Generic installation instructions Cylinder pressure • Check the regulator control is turned all the way OFF (anti-clockwise). For HydroTap, mixer tap and any optional accessories, use •...
Page 11
C res C 175 comm SECTION 10: Connect the Command Center SECTION 10: Connect the Command Center John Guest pipe and fittings CS100 models Take care to use correctly, see below : MAINS CHILLED The foam insulation supplied CHILLED MAINS Mains OUTLET OUTLET...
Select the language, date / time & drain away options • Initial commissioning screen touch COMMISSIONING 12:12 PM Language option. HydroTap G5 Language 024-H5v0.1.16 BCS100 0000000000000 H50063000US • Touch the appropriate button to select...
Page 13
SECTION 11: Commissioning SECTION 11: Commissioning Filter flush • Touch the arrow to continue when ready COMMISSIONING 12:12 PM to start using the HydroTap. • Follow the steps on-screen to flush the Your HydroTap is designed to be used frequently, do not commission until ready for use.
Page 14
SECTION 11: Commissioning SECTION 11: Commissioning Backflow Prevention purge PURGE WATER WITH CO2 12:12 PM All HydroTap models that have sparkling/carbonated water functionality • CO2 life settings should be adjusted for the INFO include the following integral Backflow Prevention. This process removes water from the sparkling size of the CO2 bottle connected.
Performance Data Sheet In addition to the HydroTap’s integral Backflow prevention Zip HydroTap G5 CS100 with ARC XX, CUBE XX, Classic XX, Wave XX, Classic Plus XX, Elite Plus Some authorities require additional Backflow Prevention to be installed to XX, ARC Plus XX, and CUBE Plus XX faucets.
Performance Data Sheet Limited Warranty- Zip Products Zip HydroTap G5 CS Home with ARC XX, CUBE XX, Classic XX, Wave XX, Classic Plus XX, Elite What Does This Warranty Cover? Plus XX, ARC Plus XX, and CUBE Plus XX faucets.
Page 17
Zip Customer. • Freight or shipping charges for sending a Zip Product to a Zip Repair Center. How to Obtain Warranty Service for The Zip Product? • Products installed in cabinetry and other types of built-in applications If during the relevant warranty period the Zip Customer finds the Zip Product that are not accessible to the service technician.
Page 19
Images in this booklet have been modified and may not be true representations of the finished goods. The terms “Zip” and “HydroTap” are registered trade marks of Zip Heaters (Aust) Pty Ltd. CS100 - Classic XX, CS100 - ARC XX, CS100 - CUBE XX, and CS100 - Wave XX have been certified by IAPMO R&T against NSF/ANSI...