Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for DFI DT200-CS
Summary of Contents for DFI DT200-CS
- Page 1 Quick Installation Guide DT200-CS MiniITX System with MXM www.dfi.com Package Contents • 1 DT200-CS System Unit • 3 M.2 Slot Screws • 2 MXM Module Screws • 1 ADDM UL Battery Addendum • Thermal Grease(X-23-7783D) Injector 1g © March 28, 2023 DFI Inc.
-
Page 2: Product Overview
Product Overview Front View USB 2.0 Power Button 2.5" SSD Slot Power LED HDD LED COM1 COM2 Quick Reference | DT200-CS... - Page 3 Rear View DC-in MIC-In HDMI Line-Out DP (From MXM) Grounding Giga LAN USB 3.0 Quick Reference | DT200-CS...
-
Page 4: Removing The Chassis Cover
The 6 screws on both front and rear sides of the system and the 8 screws on the left and right sides of the system are used to secure the cover to the chassis. Remove the screws and put them in a safe place for later use. Front View Rear View Left View Right View Quick Reference | DT200-CS... - Page 5 Step 2: Lift the cover to open the system. Step 3: The boards can be easily accessed after the chassis cover is removed. Quick Reference | DT200-CS...
-
Page 6: Installing An M.2 Card
2. Disconnect all power cords and cables. Step 1: There are 4 screws on the bottom of the system are used to secure the M.2 cover to the chassis. Remove the screws and put them in a safe place for later use. Quick Reference | DT200-CS... - Page 7 Step 2: Lift the cover to open the system. Quick Reference | DT200-CS...
- Page 8 Screw tight the card onto the stand-off with a screw driver and a stand-off screw until the gap between the card and the stand-off closes up. The card should be lying parallel to the board when it’s correctly mounted. Quick Reference | DT200-CS...
- Page 9 The board can be easily accessed and you will find the location of the MXM card socket. Step 2: Please follow the steps below to install an MXM card into the socket. Insert an MXM card into the socket at an angle while making sure the notch and key are perfectly aligned. Quick Reference | DT200-CS...
- Page 10 Screw tight the card through the holes with the motherboard to keep it steady until the gap closes up. The card should be lying parallel to the board when it’s correctly mounted. The List of Compactible MXM modules is as follows: Model Assignment Assignment P1000 P2000 T1000 1920 PTX3000 Quick Reference | DT200-CS...
- Page 11 An MXM cooler is an optional accessory, customers can purchase it if necessary. Step 1: Align the mounting screws of the cooler with the mounting holes of the module. Tighten four screws to install the cooler onto the module. Quick Reference | DT200-CS...
- Page 12 612-M3T300-000G 80W, 1290 CUDA Cores, 5.4 TFLOPS, 0~55°C MXM Quadro RTX3000 Fan PWR Y-cable for 1*3P/2.5mm to 1*3P/2.54mm to A81-009614-016G MXM(RTX3000) 1*4P/1.25mm, L=50mm MXM cooler for RTX3000 87x106.35x34 A71-110100-000G MXM Cooler MXM cooler for T1000 73x60x32.1mm Quick Reference | DT200-CS...
- Page 13 Insterting a 2.5" HDD/SDD Step 1: There is a 2.5" HDD/SDD slot on the frong side of the system. Step 2: Pull the silver latch to unlock the door. Quick Reference | DT200-CS...
- Page 14 Slide the drive into the slot until the drive is fully seated. Close the drive latch to lock the drive in place. Important: Excessive force may damage its mechanical parts. If the HDD/SSD is inserted backward into the slot, forcing the device may damage the slot. Quick Reference | DT200-CS...
-
Page 15: System Layout
System Layout USB2_5/6 COM1 COM2 LAN1 AUDIO Quick Reference | DT200-CS... - Page 16 System Fan Power DIMM1 DIO Power DIMM2 CPU Cooler 6x USB 2.0 Hub Riser Card Front Panel System Fan SATA Power 2.5" SATA SSD/HDD Tray SATA0 SATA1 LCD Panel Power LCD/eDP USB 2.0 COM1 COM2 Clear CMOS Jumper Quick Reference | DT200-CS...
-
Page 17: Jumper Settings
Jumper Settings M.2 Power M2JP204 3V3SB (default) 1-2 On 2-3 On Clear CMOS Jumper Normal (default) 1-2 On Clear CMOS Data 2-3 On Quick Reference | DT200-CS... -
Page 18: Pin Assignment
PIN Assignment X DIO Power X SATA Power Assignment Assignment 5VSB X SATA (Serial ATA) X CPU Fan Assignment Assignment Ground CTRL X DIO Assignment Assignment D_IOA0_C D_IOA1_C D_IOA2_C D_IOA3_C D_IOA4_C D_IOA5_C D_IOA6_C D_IOA7_C Quick Reference | DT200-CS... - Page 19 X USB 2.0 Assignment Assignment SBV4 SBV4 USBP_C_5N USBP_C_6N USBP_C_5P USBP_C_6P X COM (Serial) Port Assignment Assignment MDCD1(2)- MRD1(2) MTD1(2) MDTR1(2)- MDSR1(2)- MRTS1(2)- MCTS1(2)- MRI1(2)- X Front Audio Assignment Assignment Mic2-L Mic2-R N.C. Line2-R Mic2-JD Line2-L Line2-JD Quick Reference | DT200-CS...
- Page 20 LAD2 SERIRQ GND2 5VSB DFI reserves the right to change the specifications at any time prior to the product's release. This QR may be based on the product’s revision. For more documentation and drivers, please visit the download page at www.dfi.com/...
Need help?
Do you have a question about the DT200-CS and is the answer not in the manual?
Questions and answers