Table of Contents
Advertisement
Auto Launch: Configures the auto launch preference.
Disabled, CMS, Open Browser, Vsign Lite, Select
Source, and Select Application options are available.
HDMI Wake Up Enabled:
the Display will turn on with the HDMI1 input source,
when it is switched on. This feature works based on
HDMI 5V signal. When this signal is active the
Display wakes up and when the signal is inactive the
Display shuts down. You can enable or disable this
option by pressing OK.
conjunction with the Auto Source Switch feature it is
recommended to enable the Auto Source Switch
option in the Signage>Controls menu.
If any Scheduler is set this option will be inactive and
can not be set as Enabled.
Note: This feature may not be available depending on the
model of your Display.
USB
Clone to USB: Copies the database files from the
Display to a connected USB device.
Clone from USB: Copies the database files from a
connected USB device to the Display.
USB Operations: Highlight and press OK to perform
USB operations.
USB Information: Press OK to open the USB
Information menu screen. Current total space and
free space information of the connected USB device
will be displayed. You can also format the connected
USB device as device storage using the Format Disk
option in this menu (FAT32 format only) to extend the
storage capacity of your Display. After doing this, that
device will only be usable with the Display.
IMPORTANT: Formatting your USB storage device
will erase ALL the data on it and its file system will be
converted to FAT32.
USB Option: Set to Off to disable the USB ports on the
Display. You can also set this option to 5V to provide
5 volts power over USB. In this case it will still not be
available to browse the USB content via the Media
Player feature of the Display.
USB resume play: Press OK to enable or disable the
feature. When enabled, the media player will be able
to resume playing the most recently played file from
the position where it was stopped last time. When
disabled, the media player will start playing the file
from the beginning.
Note: The resume play function status is retained until the
Display is turned off (standby mode) or the USB memory
device is taken out.
Safely Remove: You can use this option to remove
the devices connected to the USB inputs of the Display
safely. Highlight this option and press OK. Wait for
the message to be displayed on the screen and then
remove your device. Failure to do so, may cause
If this option is enabled,
In order to use this feature in
problems when you connect your USB device to other
devices and you might have to format your USB device.
OPS Settings
Press OK to open the OPS Settings menu screen.
This menu cannot be displayed if the OPS
.
is not plugged in
OPS Status: Displays whether the OPS module is
on or off. Allows the change of status via soft PSON
signal (0.5s).
OPS Power: Highlight and press OK to turn the OPS
module on or off.
Power Down: Turns the OPS off via hard PSON
signal (5s).
Boot Signal: Enables or disables sending of a PSON
signal. The Display checks the status signal of the OPS
at bootup in order to turn it on by sending a PSON
signal if it is off. Some OPS's send incorrect information
on their status during the bootup of the Display, so
they seem to be on even though they are off. For such
non-standard OPS's, this option must be enabled. In
this case, a PSON signal will be send for the OPS
regardless of the received status information at bootup.
Recovery Mode: When this option is enabled and
OPS is on, if there is no video for 10 seconds it resets
hotplug. If there is no video available after 30 seconds
it reboots OPS.
OPS Always On: When this option is enabled, the
Power Mode option in the Display Settings > Sig-
nage Settings > Power Up Settings menu will be
forced to enabled (Reactive mode) and greyed out in
the menu and OPS will not be set to standby.
Scheduler Settings
Using the scheduler options you can set the Display
to turn on automatically at defined time intervals
with the defined input source setting on the desired
days of the week. Press OK to open the Scheduler
Settings menu screen. You can set up to 4 different
plans.
Highlight the desired plan option and press OK to set.
Now you will be able to define a time for the Display
to be turned on automatically. Highlight the related
option and press the OK button, then use the
directional and numeric buttons on the remote or the
virtual remote to set a time. Highlight OK and press
the OK button again when you are done.
Perform the same steps to set a time for the Display
to turn off.
Next, select the week day/s for your plan to be
activated. Highlight the desired day/s and press OK
to check. Highlight and press OK a second time to
uncheck a box. The plan will be active on the
checked days of the week.
module
17
Advertisement
Table of Contents
