Table of Contents
Advertisement
Digital Output: Set the digital sound output prefer-
ence. PCM, Bypass, and Auto options will be availa-
ble. Highlight the option you prefer and press OK to set.
Note: This option should be set to PCM instead of Auto, if
the connected external audio device does not support DD.
Otherwise, no sound will be heard from the connected device.
AVL: With this option, you can set the Display to auto-
matically level out sudden volume differences. Typically
at the beginning of adverts or when you are switching
sources. Turn this option on/off by pressing OK.
HDMI/ARC latency: Adjust the delay value for HDMI/
ARC.
Audio Output Latency: Adjust the delay value for
SPDIF.
Reset: Reset the sound settings to factory default
settings.
Network & Internet
You can configure your Display's network settings
using the options of this menu.
Wi-Fi: Turn the wireless LAN (WLAN) function on
and off. Highlight and press OK to turn this function
on and off.
Available networks
When the WLAN function is turned on, a few available
wireless networks will be listed. Highlight See all and
press OK to see all networks. Select one and press OK
to connect. You may be asked to enter a password to
connect to the selected network, in case the network
is password protected.
Other Options
Add new network: Add networks with hidden SSID's
(network name). You can use this option in order to
connect to the hidden networks by entering their names
manually. This item will not be available if the Wi-Fi
option is not turned on.
Networked Standby Mode: This is a standard
that allows a device to be turned on or woken up by
a network message when it is in standby mode.
Highlight and press OK to turn this function on and
off. Refer to Networked Standby Mode section for
more information.
Ethernet
Under the Ethernet caption, you can see the LAN
status (as Connected - Not connected) and also
MAC/IP addresses if connected. You can also set a
proxy server and change the IP settings using the
related options.
Connected/Not connected: Displays the status of
the connection (via Ethernet), IP and MAC addresses.
Proxy settings: Set a HTTP proxy for browser
manually. This proxy may not be used by other apps.
IP settings: Configure your Display's IP settings.
Signage Settings
Device Info
Display device information menu options.
Set ID: Sets the device ID. You can set a number
using the virtual keyboard in order to identify your
Display.
Software Version: Displays current software
version. Press OK to open the update centre. In
addition to the current software version, the last
update date information can be found here. The
CHECK UPDATE option will be highlighted. Press
OK to start a manual search for a software update.
To do this, your Display should be connected to
the Internet. If any update is found, you can
download and install the new software using the
related options. Follow the on-screen instructions
to complete the process.
Serial Number: Displays serial number of the
Display. (Cannot be changed by the user)
Model Name: Displays model name of the Display.
(Cannot be changed by the user)
Save Model Information: Copies the model
information data of the Display to a connected
USB device.
Display Life Time: Displays the lifetime of the
Display in hours.
Controls
OSD Orientation: Sets the OSD (On Screen Display)
rotation of your Display. Landscape, Portrait1,
Portrait2.
Pixel shift: Enables or disables pixel shifting. This
option can be used to avoid image retention (after
image effects) that can occur when displaying fixed
patterns or still images for long periods of time. If
enabled, the picture and OSD (On-Screen Display)
will be shifted at specified time intervals.
No Signal: Sets the behavior preference of the
Display, when no signal is detected from the currently
set input source. Failover and Input Search options
are available.
If Failover is selected the Display checks the
connected USB device for available files to play. If no
playable files are available or there is no USB device
connected to the Display, the No Signal Image will be
displayed. If there isn't any No Signal Image available,
No Signal OSD will be displayed on the screen. The
setting of the USB Auto Play option in the Display
Settings > System Settings > More menu is not
important, in Failover mode it will function anyway.
If Input Search is selected, available input sources
will be listed. Highlight the options you want and press
15
Advertisement
Table of Contents
