Table of Contents
Advertisement
OK to select. The Display will search all selected input
sources consecutively to find signal. If no signal is
detected from other available sources, the Display will
turn off automatically after completing a cycle.
How to install No Signal Image
Install the file you want to use onto the root
directory of any USB storage device and name it
as "NoSignalImage.png". Connect the USB
storage device to the Display. Highlight the USB
Operations option in the Display Settings>Signage
Settings>USB menu and press OK.
No Signal Delay: Sets a delay value to the 'No
Signal' preferences when the Display is in No Signal
state. After the set delay time has expired 'No Signal'
preferences will be applied.
No Signal Power Off: When enabled the Display will
turn itself off after a specified period of time (defined
in the No Signal Timer option), if no signal is received
from the selected source.
This feature will only work if all of the following
circumstances occur:
• No Signal option is set to Failover.
• USB device is not connected to the Display / USB
device is connected but there are no playable files
installed on the USB device.
You can define a shut-off timer for
No Signal Timer:
the Display using this option. When the Display is
in No Signal state and No Signal OSD is displayed
on the screen, it will go into standby mode after the
time set here has expired.
Panel Lock: Set to On to prohibit the use of the
button/s on the Display.
RCU Inhibit: Set to On to inhibit the use of the
remote. Remote control will function in standby mode
independently from the setting of this option.
To turn this option off and be able to use the remote
again, press the MENU/M-1-9-7-3-Back/Return
buttons on the remote consecutively. The Signage
Settings menu will appear. Enter the Controls menu
and set this option to Off.
UART0: Select ASCII/HEX protocol for UART 0.
Default value is ASCII. There is no need to restart
the Display after selection in order to work with the
protocols correctly. If the selection is changed, the
latest selected protocol will be preserved and
started when the Display is booted up.
Note that ASCII/HEX selection is not working while
debug logs are enabled. If it is wrongly changed to
HEX while debug logs are enabled, revert the
selection to ASCII and reboot the Display in order
to correct the debug logs and the ASCII protocol
behaviour.
Also note that HEX protocol will work with the baud
rate value 19200 for UART 0.
Also note that HEX protocol will work with the baud
rate value 19200 for UART 0.
UART1: Select ASCII/HEX protocol for UART 1.
Default value is HEX. There is no need to restart the
Display after selection in order to work with the
protocols correctly. If the selection is changed, the
latest selected protocol will be preserved and started
when the Display is booted up.
Note that ASCII/HEX selection is always working as
expected. It does not matter if the debug logs are
enabled or not.
Also note that HEX protocol will work with the baud
rate value 9600 for UART1
Menu Lock: You can block the usage of the menu
button on the remote by setting this item as All menus.
When you press the Menu or Signage button, or
highlight the Signage Settings on the Home Screen
and press OK, you will be asked to enter the PIN that
you have defined during the initial setup process. If you
didn't defined a PIN during the initial setup, you can
use the default PIN. Default PIN is set to 0000. Set to
Off to disable this function.
Auto Source Switch: If this option is enabled the
Display will switch to the currently active HDMI source
automatically when a device is connected to the
Display through the HDMI1 or HDMI2 input socket.
Set to Enabled to enable this feature.
When the HDMI source is removed the Display will
switch to other active HDMI source. If there isn't any
other device connected to the Display and the HDMI
Wake UP option for the related HDMI source is enabled
the Display will switch into the standby mode.
There is also a 3-second restriction for the successive
connected HDMI sources. This means, second HDMI
device must be plugged in 3 seconds after the first
HDMI device is plugged in.
Note: This feature applies for HDMI1 and HDMI2 input sockets
only. Refer to the General View section to see the HDMI inputs.
Bluetooth: Switches on or off the Bluetooth function-
ality. Set to Enabled to enable this feature.
Power Up Settings
Power Up Mode: Configures the power up mode
preference. Always On, Standby, and Last State
options are available.
Power Mode:
If this feature is enabled the Display
can be turned on again with the RS232 and LAN
commands if it is turned off through it. Press OK to
enable or disable the feature.
Enabled - Reactive mode
Disabled - Eco mode
Power On Delay: Sets a delay value at power on. This
value can be set from 0 to 2000 ms in steps of 100 ms.
The Display will turn on after the set delay time has
expired.
16
Advertisement
Table of Contents
