Subscribe to Our Youtube Channel
Related Manuals for BOXLIGHT ProColor
Summary of Contents for BOXLIGHT ProColor
- Page 1 ProColor Flat Panels 151 NE State Hwy 300, Ste A Belfair, WA 98528 360.464.2119 www.boxlight.com...
-
Page 2: Table Of Contents
Contents Specifications Important safety Instructions --------------------------------------------------------- 2, 3 84” System Specifications ------------------------------ 25 84” LED Panel Specifications --------------------------- 25 Safety Precautions Ratings of Environment -------------------------------- 25 ---------------------------------------------------- 4, 5, 6, 7 Input / Output Description ---------------------------- 26 70” System Specifications ------------------------------ 28 Instructions 70”... -
Page 3: Important Safety Instructions
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. Do not install the product in a place where water can splash onto it or near devices such as air conditioners where water may accumulate. - Page 4 18. Use the cables provided with this product, and be sure that other cables used are properly shielded. 19. Conduct a safety inspection after installation or repair to confirm that the above precautions have been adhered Note: Prolonged use of the display at high volume may cause damage to your ears. This symbol is intended to alert the user to the presence of un-insulated "dangerous voltage"...
-
Page 5: Safety Precautions
Safety Precautions Note The color and appearance of the product may vary depending on the model, and the product specifications are subject to change without prior notice for reasons of performance enhancement. Please read the following safety instructions as they are designed to prevent damage to property and harm to the user. - Page 6 This may cause electric shock or fire. Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage. Insert the power plug firmly so that it does not come loose. A bad connection may cause fire. ...
- Page 7 Installation Failure to adhere to the following may cause serious damage to your LED Display. Do not drop the LED Display when moving it. This may cause damage to the product or the person carrying it. Keep any flammable objects such as candles, insecticides or cigarettes away from the product. Otherwise, this may cause fire.
- Page 8 Clean When cleaning the LED Display case or the surface of the screen, wipe with a dry or slightly moistened, soft fabric. Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle. This may cause a malfunction, electric shock or fire.
-
Page 9: Package Contents
If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Components List LED Display Manual: User Manual (CD) Cables & Others: USB For TOUCH Power plug Remote Control & PEN *2 3V Battery(CR-2025x1) Options: ProColor-Tray (general use) USB Cable(2Ea), Screw(14Ea), Bracket (2Ea) -
Page 10: Front
Front IR SENSOR 1) POWER( Turns the LED Display On/Off. 2) LED Shows Power ON mode -- BLUE Shows Power Saver mode by blinking RED. Shows Power OFF mode -- RED. 3) SOURCE (INPUT Switches from PC mode to Video mode. Changing the source is only allowed for external devices that are connected to the LED Display at the time. - Page 11 Input / Output Description - 84” only 1. SPEAKER Out L. (2ch 10W , 8 Ohm ) 2. SPEAKER Out R. (2ch 10W , 8 Ohm ) 3. AUDIO LINE Out 4. PC AUDIO Input 5. PC RGB Input 6. DISPLAY PORT Input 7.
-
Page 12: Remote Control
Remote Control How to insert the battery. Insert the battery with the polarities facing as shown. -
Page 13: Connection
Connection Connecting a Computer for TOUCH 1. Connect the LED display’s power cord to the display and the appropriate electrical plug. Turn the display on by pressing the Power button on the display or remote. 2. Using the D-sub (Analog) connector on the video card: Connect the D-sub to the 15-pin, RGB port on the back of your LED Display and the 15 pin D-sub port on the computer. -
Page 14: Adjusting The Led Display
Adjusting the LED Display Turning the Display On/Off Once the display is connected, use either the Power button on the front of the display, or the power button found on the remote control. Confirm your display’s status by checking the LED light on the front of your display. Status Status of the Monitor Blue... - Page 15 ◆ Custom adjustment CSM Press the ▲/▼ buttons to highlight the Red, Green or Blue level. Next, press the ENTER button to select one of them. Once selected, press the ◁/▷ buttons to adjust the Red, Green, or Blue level. ◆...
-
Page 16: Sound Menus
Sound Menus ◆ Press [MENU] Button. The OSD Main MENU will be shown. ◆ Entering the Sound MENU Press the ▲/▼ buttons to move up to the SOUND Menu. Press the ENTER button to enter the menu. ◆ Select Sound Status Mode Press the ▲/▼... -
Page 17: Time Menus
◆ Equalizer Adjustment Press ◁ or the Menu Button to move or go back to the previous menu options. Press ▲/▼ Button to highlight the Equalizer Menu, press the ENTER button to view the settings. Press the ▲/▼ buttons to highlight one of the 0.1/0.5/1.0/5.0/10kHz values. - Page 18 Press the ▲/▼ buttons to adjust the time, and press the ENTER button to confirm it. ◆ Setup System OFF Time Press ◁ or the Menu Button to move or go back to the previous menu options. Press the ▲/▼ buttons to highlight Off Time, and press the ENTER button to select it.
-
Page 19: Input Menus
◆ Setup Auto Sleep If Auto Sleep mode is ON, the screen will go to sleep when no input signal is received and 5 minutes have passed. Press ◁ or the Menu Button to move or go back to the previous menu options. Press the ▲/▼... -
Page 20: Setup Menus
◆ Input source select Press the ▲/▼ buttons to highlight either PC/HDMI1/ HDMI2/HDMI3/DP. Once the desired input is highlighted, press the ENTER button to select it. Only sources that are connected to the display can be selected. ◆ Selecting the screen ratio Press ◁... -
Page 21: Language
◆ Change the OSD Language Press the ▲/▼ buttons to select Language, and press the ENTER button to view and select available languages. Use the ▲/▼ buttons to highlight the language you would like to use and press the ENTER button to select it. ◆... - Page 22 ◆ Setup Reset Press ◁ or the Menu Button to move or go back to the previous menu options. Press the ▲/ ▼buttons to highlight Reset. Press the ENTER Button. Press the ▲/▼ buttons to select On Off, and press the ENTER button to confirm.
- Page 23 Mechanical Layout 84” LED INTERACTIVE Dimensions...
- Page 24 Mechanical Layout 70” LED INTERACTIVE...
- Page 25 .com...
Need help?
Do you have a question about the ProColor and is the answer not in the manual?
Questions and answers