Related Manuals for Teknik 5427127
Summary of Contents for Teknik 5427127
- Page 1 Teknik www.teknikoffice.co.uk Welcome to the big kid table. Counter Height Work Bench Vintage Oak Model 5427127...
- Page 2 Table of Contents Assembly Tools Required Part Identifi cation No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identifi cation Assembly Steps 5-16 Rubber Mallet Warranty Part Identifi cation å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other.
- Page 3 Now you know Part Identifi cation our ABCs. Page 3...
-
Page 4: Table Of Contents
Hardware Identifi cation å Screws are shown actual size. You may receive extra hardware with your unit. 10F TWIST-LOCK HIDDEN CAM - 14 CAM DOWEL - 14 ® FASTENER - 8 WOOD DOWEL - 28 GLUE - 1 SCREW COVER - 44 CAM COVER - 4 BLACK 1-7/8"... - Page 5 Step 1 Assemble your unit on a carpeted fl oor or on the empty å carton to avoid scratching your unit or the fl oor. To begin assembly, push a SAUDER TWIST-LOCK® å FASTENER (10F) into the large holes in the TOP SHORT BRACES (G).
-
Page 6: Hidden Cam
Step 2 Push fourteen HIDDEN CAMS (1F) into the OUTER LEG å PANELS (D), TOP LONG BRACES (F), and TOP CENTER BRACE (H). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM. Do not tighten the HIDDEN CAMS in this step. Push these two HIDDEN CAMS completely down in the holes. - Page 7 Step 3 Slide the notched edges of the LEG PANELS (E and K) å into the grooves in the OUTER LEG PANELS (D). NOTE: The fi nished surfaces on the LEG PANELS (E å and K) should all face out. Edge with CAM DOWEL Groove...
-
Page 8: 15F
Step 4 First, fi ll the holes in the in the short edges of the SHORT å LEG PANELS (C) 1/4 to 1/2 full with GLUE (54M). Then, insert eight WOOD DOWELS (15F) into the holes. Wipe away the excess GLUE. Next, fasten the SHORT LEG PANELS (C) to the LEG å... - Page 9 Step 5 First, fi ll the holes in one edge of each of the LOWER å SHORT BRACES (I) 1/4 to 1/2 full with GLUE (54M). Then, insert eight WOOD DOWELS (15F) into the holes. Wipe away the excess GLUE. Next, fi...
- Page 10 Step 6 Fill the holes in one end of each of the LONG LEG å PANELS (B) 1/4 to 1/2 full with GLUE (54M). Next, place the LONG LEG PANELS (B) onto the WOOD å DOWELS in the LOWER SHORT BRACES (I). Wipe away the excess GLUE.
- Page 11 Step 7 Fasten the TOPS (A) to the TOP SHORT BRACES (G). å Tighten eight TWIST-LOCK® FASTENERS. ® How to use the SAUDER TWIST-LOCK FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER.
- Page 12 Step 8 Fasten the TOP LONG BRACES (F) and TOP CENTER BRACE (H) å to the TOPS (A). Tighten ten HIDDEN CAMS. Fasten the TOP LONG BRACES (F) to the TOP SHORT å BRACES (G). Use four SILVER 2" FLAT HEAD SCREWS (57S). Fasten the TOP LONG BRACES (F) to the TOP CENTER å...
- Page 13 Step 9 NOTE: You will need somone's help in this step. å First, fi ll the holes in the edge of the TOP SHORT BRACE (G) å 1/4 to 1/2 full with GLUE (54M). Then, insert four WOOD DOWELS (15F) into the holes. Wipe away the excess GLUE. Next, place a dab of GLUE (54M) onto each WOOD DOWEL.
- Page 14 Step 10 NOTE: You will need someone's help in this step. å Fill the outermost holes in the short edges of the LOWER LONG å BRACE (J) 1/4 to 1/2 full with GLUE (54M). Then, insert four WOOD DOWELS (15F) into the holes. Wipe away the excess GLUE. Next, place a dab of GLUE (54M) onto each of the WOOD DOWELS in å...
-
Page 15: Glue
Step 11 First, fi ll the holes in the edge of the TOP SHORT BRACE (G) 1/4 to 1/2 full with GLUE (54M). Then, insert four WOOD å DOWELS (15F) into the holes. Wipe away the excess GLUE. Next, place a dab of GLUE (54M) onto each WOOD DOWEL in the TOP SHORT BRACE (G) and LOWER LONG BRACE (J). å... - Page 16 Step 12 Carefully stand your unit upright. å Center a SCREW COVER (18P ) over the head of each SCREW and gently tap in with your å rubber mallet. Using your rubber mallet, gently tap a CAM COVER (13P) onto each HIDDEN CAM. å...