Advertisement
STEP 1
Install the side brackets (5).
Image
Qty
Spec
4
M6
A
x4
4
M6
8
M6
F
12
M6
4mm
16
St4.2
Allen Key
1
4x4mm
5
A
4
5
A
STEP 2
Install the lifting columns (2).
6
Insert the lifting columns
D
x8
(2) into the ends of the
supporting beam (4). Fix the
2
lifting columns using screws
(D) with the allen key (F).
3
F
4mm
D
2
F
7
D
6
4
F
C
STEP 4
Install desktop.
F
1
E
C
x12
1
1
E
E
E
E
5
F
For each component, always start
A
all screws in their threads before
A
tightening any screw fully.
5
F
A
5
4
2
F
D
Attach the side brackets (5) to the ends of the supporting
beam (4) using screws (A) with the allen key (F).
4
STEP 3
Install the feet (1).
C
x8
F
F
1
C
4
Place the feet (1) on the bottom of
the lifting column (2). Fix the feet
using screws (C) with allen key (F).
1
2
2
2
Loosen
1
2
E
Adjust
The expansion distance of
the supporting beam can
E
be adjusted according to
the actual use.
Tighten
When the supporting beam is
greater than 1720mm, the installation
method is as Method 2 in Step 6.
5
4
STEP 5
TOP TIP
STEP 6A
F
B
4mm
F
2
STEP 6B
Loosen
2
Loosen
B
D
Adjust
Adjust
F
Tighten
Tighten
Common fault treatment
7
E
E
E
Install the control panel.
6
6
6
Install the cable management tray (Method 1)
x4
3
4mm
3
3
4
B
4
B
4
B
Install the cable management tray (Method 2)
x4
x4
3
3
3
4mm
B
B
D
D
4
4
D
D
D
B
B
B
Common fault treatment
Attention
Adjust
Tighten
Tighten
Tighten
7
7
7
Power port
Power port
Port for cable
Port for
connected to the
Power port
hand switch
lifting column
Port for cable
Port for
connected to the
hand switch
Port for cable
lifting column
Port for
connected to the
hand switch
lifting column
Slide one side
3
1
Tighten
Slide one side
3
1
Tighten
Slide one side
3
1
Tighten
Buckle the other side
2
2
Buckle the other side
2
Buckle the other side
Firstly, rotate the screws (B) incompletely into the supporting beam (4)
with allen key (F), which means do not tighten them. Next, slide one side
of the cable management tray (3) into the screws (B), then the other side.
Finally, tighten the screws (B) with allen key (F).
When the supporting beam
stretches over 1720 mm, the cable
management tray needs to be
B
D
mounted on the middle of the
supporting beam.
4
Do not stretch the support
beam beyond this hole
Attention
Common fault treat
The following tips will help y
and error.If the fault you me
supplier. Only themanufact
Common fau
and correcting those fault a
Common faul
The following tips w
Fault phenomeno
and error.If the faul
supplier. Only them
No response while long pr
The following tips w
and correcting thos
down arrow after connect
and error.If the fault
a power supply
supplier. Only thema
and correcting those
Fault phen
No response while pressi
arrow/ down arrow after
connected with a power s
No response whi
Fault pheno
down arrow after
a power supply
No response while
Rising in a low speed
down arrow after c
No response whi
a power supply
arrow/ down arro
The motor not move as ins
connected with a
No response while
arrow/ down arrow
Go down but not go up
connected with a
Rising in a low
The motor not mo
Rising in a low s
Downward sliding
The motor not mov
Go down but n
Frequently Reposition
Go down but no
Downward slid
Overwork
（Duty cycle: Max 2min on/18m
Downward slidi
Frequently Re
Not enough up&down h
Frequently Rep
Over
（Duty cycle: Max 2
Overw
（Duty cycle: Max 2m
Not enough up
Not enough up&
Waste disposal
Waste dispos
Waste dispos
Advertisement
