Arrow HAFS233 Assembly Instructions

HEIGHT CONTROL INSTRUCTIONS
POSITION preset buttons
UP button
LED display
ALERT button
DOWN button
MEMORY button
ADJUST HEIGHT
Press UP or DOWN button. Display shows the current height.
MEMORY FUNCTION
Press UP or DOWN button to adjust the desk to the required
height. Press MEMORY button to store the height. The display
will show . Now press a POSITION button to store the height
on preset 1, 2 or 3. The display will show , or . Press a
POSITION preset button to adjust the desk to the saved height.
ANTI-COLLISION SENSITIVITY
Press UP and DOWN buttons at the same time to adjust the
sensitivity of the anti-collision system. 3 levels of sensitivity are
available, low , medium or high .
TROUBLESHOOTING
Symptom Possible Cause
Cables not connected properly.
No response from a long press of the DOWN
1 Power supply off.
button after power is connected.
Other fault.
Overloaded (maximum load 125kg
including desktop).
2 Desk does not lift when up button is pressed.
Power or connection fault.
Other fault.
Duty cycle exceeded 2 minutes on
Cuts out during use.
- 18 minutes off.
3
Display shows 'E01' or 'E02' .
Other fault.
Factory reset required.
4 Desk will not go high enough or low enough.
Other fault.
5 Display shows Reset required.
SAFETY
Assembly
• Only to be assembled by a competent person - check carefully for complete and correct assembly before use.
• Dispose of packaging in an environmentally-friendly manner. Recycle cardboard and paper.
• Keep plastic and small parts out of the reach of children. Danger of suffocation/choking.
Product care
• Unplug before servicing and cleaning.
• Wipe surfaces with a damp microfibre cloth - do not spray cleaner near electrical parts or connections.
• Do not use chemical or abrasive cleaners.
• Do not leave work surface wet.
• Use a drinks coaster to prevent marks.
• Use a mouse mat to prevent abrasion of the work surface.
End of life disposal
• This product must be recycled in accordance with WEEE directives.
Manufactured for Arrow Group Global Ltd
TECHNICAL DATA
Column Number 3
Maximum Load 125kg
Maximum Speed 38mm/second
Input Voltage 100-240v
Lowest Position 580mm
Highest Position 1230mm
Desktop Size Width 1100-1900 mm
Depth 700 or 800mm
Duty Cycle Continuous operation for 2 mins
at most after pause for 18 mins
Operating Temperature Range 0-40°C
REMINDER FUNCTION
Press ALERT button to activate. The display will show . Wait 2 seconds
for the display to flash then press the UP or DOWN button. The screen
will display which is the default reminder duration of 45 minutes. Now
press any button to save this setup, or wait 5 seconds and the system
will save automatically. The timer will countdown to zero. During the
countdown press any button to reset the countdown timer. When it
reaches zero the buzzer will activate with a 10 second tone. Within 10
seconds press any button to reactivate the countdown timer. If no button
is pressed during 10 seconds there will be another reminder buzzer after
5 minutes. If no button is pressed during the second buzzer the reminder
function will switch off automatically. Press and hold the ALERT button to
switch off the reminder function. The display will show .
Remedy
Check connections and retry.
Check power supply.
Contact your supplier.
Technical data
Check and lighten load if necessary.
Max. Weight Capacity
Check power supply and connections
in Symptom 1.
Contact your supplier.
Wait 30 minutes for the motors to cool
and retry.
Component list
Contact your supplier.
Press 'M' and '3' buttons together for more
than 3 seconds and wait for 2 long beeps.
Contact your supplier.
Press DOWN button until desk reaches it's
lowest position and rebounds to stop.
No. Part
1
No. Part
3
Cable Management Tray
No. Part
5
Side Bracket
No. Part
7
Power Plug
sales@arrow.gb.net | +44 (0)1502 533433
3 Stage Height Adjustable Desk (HAFS233)
Item No.: ET223(IB)
Installation guide
Accessory list
Attention: The drawings below are for guidance only and they may differ
slightly from the product and fittings received. Please contact our customer
service department should you have any queries.
No. Image
A
B
C
UNPACKING INSTRUCTIONS
D
Carefully open the carton, and lay out the parts E
3
Column Stage
on a protective surface to avoid damage. Check
F
125KG
pack contents against the parts list to ensure all
580-1230mm
Height Range
components have been recieved. Do not use damaged
1100-1900mm
Width Range
or defective parts. Carefully read all instructions before
starting assembly of the desk.
PARTS OVERVIEW
Qty No. Qty
Part
2 2 2
Feet Lifting Column
Qty No. Part Qty
1 4 1
Supporting Beam
(Control Box included)
Qty No. Qty
Part
1
6
2 5
Hand Switch
(Option)
Qty 2
1
1
Assembly Instructions
Qty
Spec
4
M6
5
4
M6
8
M6
PARTS LIST
12
M6
Part Description
16
St4.2
Feet
Allen Key 1
4x4mm
1
Lifting Column
2
Cable Management
Tray
3
Supporting Beam
w/ Control Box
6
4
Side Bracket
3 5
Hand Switch
6
7
Mains Power Lead
7
F
A
4
A
Qty Part Description Qty
M6
A
2 4
M6
2
F
B
2 4
D
M6
C 4
1 8
M6
D
1 12
ST4.2
F 1
E
2 16
C
Allen Key
2
4mm/5mm
F
1 1
1