Related Manuals for Labnet Orbit S2020-P4-B
Summary of Contents for Labnet Orbit S2020-P4-B
- Page 1 Labnet Orbit™ Digital Shakers Instruction Manual Catalog Numbers: S2020-P4-B S2030-300-B S2030-1000-B S2040-1900 S2020-P4-B-230V S2030-300-B-230V S2030-1000-B-230V S2040-1900-230V...
-
Page 2: Table Of Contents
Table of Contents 1.0 Introduction ................. . .1 2.0 Safety Precautions . -
Page 3: Introduction
Do not shake inflammable or explosive samples or use the unit in an inflammable or explosive environment. 3 .0 Specifications The casings of the Labnet Orbit P4, 300, and 1000 are made of plastic. Bottom cover and upper plate are made of steel plate varnished with high resistant polyurethane lacquer. - Page 4 22 lbs. (10 kg) Dimensions (W x L x H) 15.3 x 18.3 x 6.2 in. (39 x 46.5 x 16 cm) Weight 68.35 lbs. (31 kg) Ambient Operation Range 5°C to 40°C, up to 85% RH, non-condensing LABNET ORBIT DIGITAL SHAKERS...
-
Page 5: Installation
(Basic, class B), and it is in compliance with IEC 61326-1:2020. The device may experience a restart during overvoltage events (surges) or voltage interruptions in mains power supply. The Labnet Orbit™ Digital Shakers is designed to be safe when operated under the following conditions: Indoor use ... -
Page 6: Operating Instructions
If they are worn out, you should replace them with new stabilizers and set to appropriate height. Labnet Orbit 1000 and Orbit 1900 The Orbit 1000 and Orbit 1900 shakers have a variety of platforms to meet most shaking needs. These platforms mount to the shakers via four mounting platforms which easily plug into four rubber mount points on the top of the shaker. -
Page 7: Basic Operation
5.2. Basic Operation Press the POWER switch on control panel. The Labnet Orbit™ Digital Shaker automatically detects supply frequency of 50 or 60Hz, and displays F50 or F60. POWER TIME Encoder START STOP Push Then the display switches to show the set time and illuminates the Time light. -
Page 8: Additional Operations
If you want to view the set value for TIME during shaking, rotate the encoder knob for ONE CLICK right (+) or left (-). Time signal light will then flash for 2 sec., and the display will show the set TIME and the light will stop flashing. LABNET ORBIT DIGITAL SHAKERS... -
Page 9: Troubleshooting
Should you have a question about the operation of the Labnet Orbit™ Digital Shakers or if service is required, contact your Corning representative. Do not send in a unit for service without first calling to obtain a repair authorization number. Should the unit require return to Corning for service, it should be properly packed to avoid damage. -
Page 10: Accessories
Orbit 1000 (max. 5) Orbit 1900 (max. 10) S2040-01 Clamp for 1L Erlenmeyer flask Orbit 1000 (max. 4) Orbit 1900 (max. 6) S2040-02 Clamp for 2L Erlenmeyer flask Orbit 1900 (max. 5) LABNET ORBIT DIGITAL SHAKERS... -
Page 11: Limited Warranty
9.0 Limited Warranty Corning Incorporated (Corning) warrants that this product will be free from defects in material and workmanship for a period of one (1) year from date of purchase. CORNING DISCLAIMS ALL OTHER WARRANTIES WHETHER EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE. - Page 12 To request certificates, please contact us at www.labnetlink.com. Warranty/Disclaimer: Unless otherwise specified, all products are for research use or general laboratory use only.* Not intended for use in diagnostic or therapeutic procedures. Not for use in humans. These products are not intended to mitigate the presence of microorganisms on surfaces or in the environment, where such organisms can be deleterious to humans or the environment.
Need help?
Do you have a question about the Orbit S2020-P4-B and is the answer not in the manual?
Questions and answers