turck EZ-track LTX R10 Series Manual
Hide thumbs
Also See for EZ-track LTX R10 Series:
- Instructions for use manual (30 pages) ,
- Manual (20 pages) ,
- Operating instructions manual (24 pages)
Subscribe to Our Youtube Channel
Related Manuals for turck EZ-track LTX R10 Series
Summary of Contents for turck EZ-track LTX R10 Series
- Page 1 Your Global Automation Partner EZ-track® LTX R10 Series Digital Output Manual Manual...
-
Page 2: Table Of Contents
EZ-track in such a way that it cannot be damaged in transit. Turck Inc. | 3000 Campus Drive, Minneapolis, MN 55441 | T +1 800 544 7769 | F +1 763 553 0708 | more@turck.com | www.turck.com... -
Page 3: Chapter 1: Ltx R10 Digital Output Overview
Chapter 1: LTX R10 Digital Output Overview The LTX R10 Digital is a magnetostrictive Linear Displacement Transducer (EZ-track) for highly accurate continuous machine positioning in a variety of industrial applications. This sensor is built to withstand the most severe environmental conditions and is completely absolute. This means that power loss will not cause the unit to lose position information or require re-zeroing. -
Page 4: Chapter 2: Installing
The diameter of this magnet assembly should not be more than 0.2" away from the rod. Split magnet assemblies outside of this range will cause signal loss. Turck Inc. | 3000 Campus Drive, Minneapolis, MN 55441 | T +1 800 544 7769 | F +1 763 553 0708 | more@turck.com | www.turck.com... -
Page 5: Installing In A Hydraulic Cylinder
To install the magnet assembly, perform the following steps: 1. Slide the magnet assembly over the EZ-track rod. 2. Mount the magnet to the non-ferrous, movable portion of the device being controlled using non-ferrous screws. 1. LTX R10 2. LB-R10 3. - Page 6 For assistance in this task, refer to the information provided by the cylinder manufacturer. Turck Inc. | 3000 Campus Drive, Minneapolis, MN 55441 | T +1 800 544 7769 | F +1 763 553 0708 | more@turck.com | www.turck.com...
- Page 7 1. O-ring 2. Optional rod bushing 3. Standard 4-hole magnet 4. Magnet spacer 5. 0.5" bore minimum Figure 2-2: Mounting EZ-track in a Hydraulic Cylinder Notes: 1. If face of port is on a machined surface, dimen- sions 1.180 and .094 need not apply as long as R.008/.0004 is maintained to avoid damage to the o-ring during assembly.
-
Page 8: Chapter 3: Wiring
Magnet Magnet pulse Note: 2.5" minimum distance between each magnet Figure 3-4 LTX R10 RS Turck Inc. | 3000 Campus Drive, Minneapolis, MN 55441 | T +1 800 544 7769 | F +1 763 553 0708 | more@turck.com | www.turck.com... -
Page 9: Rs (Start/Stop)
Recirculations The method used to improve the resolution of a system using a digital LTX R10. The"on” Time of a pulse width output is multiplied by a specific factor (from 1-255). This multiplication provides more counting time for the counter in the customer’s electronics, thus improving the resolution. -
Page 10: Features
+7 and +30 VDC. * See Section 3.7 page 11: Specifications for more information on power consumption. Turck Inc. | 3000 Campus Drive, Minneapolis, MN 55441 | T +1 800 544 7769 | F +1 763 553 0708 | more@turck.com | www.turck.com... -
Page 11: Specifications
If reading is between 7 and 30 VDC, turn power supply off and go to step 7. If reading is below 7 VDC, either your power supply is not providing enough power or the EZ-track’s cable possibly has a short/open. Readings of no voltage or minimal voltage (less than 5 volts) may be due to short/open in the cable. -
Page 12: Part Numbering System
2 meter Cable, Right Angle Cordset WKC 6T-2/S618 Mounting Bracket Kit MB-R10 4 meter Cable, Right Angle Cordset WKC 6T-4/S618 Turck Inc. | 3000 Campus Drive, Minneapolis, MN 55441 | T +1 800 544 7769 | F +1 763 553 0708 | more@turck.com | www.turck.com... - Page 13 Notes:...
- Page 14 Notes: Turck Inc. | 3000 Campus Drive, Minneapolis, MN 55441 | T +1 800 544 7769 | F +1 763 553 0708 | more@turck.com | www.turck.com...
- Page 15 Notes:...
- Page 16 28 subsidiaries and over 60 representations worldwide! Printed in USA ©2016 by Turck Inc. All rights reserved. No part of the www.turck.com B1408 10/16 publication may be reproduced without written permission.
Need help?
Do you have a question about the EZ-track LTX R10 Series and is the answer not in the manual?
Questions and answers